AVSPARE.COM
parts catalog

AFTERCOOLER GP-TREATED WATER 3156858 - Caterpillar



3156858 AFTERCOOLER GP-TREATED WATER Caterpillar parts 3406E AFTERCOOLER
Rating:
24
Alternative (cross code) number:
CA3156858
315-6858
3156858
Caterpillar 3156858 AFTERCOOLER GP-TREATED WATER

Buy AFTERCOOLER GP-TREATED WATER 3156858 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: 3156858:

MARINE ENGINE  3406E   Caterpillar
Number on catalog scheme: 8
 
  For full view, you need register

Information:

(1) Torque for nut ... 14 4 N m (10 3 lb ft)(2) Torque nut to where 20 2 N (4.5 .4 lb) of force is required to move lever (4).(3) Torque for jam nuts ... 5.0 0.5 N m (45 5 lb in)(9) Hand tighten nut against weld nut, then back nut off one-quarter turn.Adjustment:
1. Put lever (4) in the FULL LOWER (forward) position.2. Rotate the spring loaded rotary sensor (7) 7.5 0.5 degrees from its stop. Turn the adjustment link (8) to line up bolt (6) with the hole. Assure that the 7.5 0.5 degrees is maintained at lever full lower when the bolt and jam nuts (3) are tighten.3. Remove bolt (6). Turn rod end (5) counterclockwise (lengthen distance between rod ends) 3 1/2 turns.4. Torque jam nuts (3) on rod (8) to 5.0 0.5 N m (45 5 lb in). Keep the face of rod end (5) parallel to sensor control (7).5. Install washers on each side of rod end (5). Torque bolt (6) to sensor control (7). Bolt (6) is a METRIC fastener.Hitch Sensor Linkage Adjustment
The hitch sensor linkage can only be properly adjusted when the lever linkage has been properly adjusted FIRST.1. Fully lower the hitch. Put control lever (4) in the FULL LOWER (forward) position. Recheck to be sure hitch and lever are in the FULL LOWER position. Linkage adjustment will not be correct if they are not.2. Place mode switch (10) in the "OPERATING" position. Turn the key switch to the ACC position.3. Find the four LED's in control module (21). The LED's are located in the control module, which is visible from the operators seat by lifting out the ashtray. Yellow LED (19) will be blinking a two flash pattern or be ON steady. If the LED is ON steady, go to Step 7. If the LED is blinking the two flash pattern, the hitch and lever are not synchronized (not in the correct relationship to each other) and need to be adjusted.4. Rotate sensor control group (11) back and forth through its full travel range. Find the point (place when rotating) where yellow LED (19) is ON steady and either green LED (18) or (20) is ON.5. Rotate sensor control group (11) slowly [left or right-depending if LED (18) or (20) is ON and about 7.5 degrees from the stop] until only yellow LED (19) is ON.6. Adjust rods (14), (15) and (16) so bolt (13) aligns with the bolt hole in plate (12). Assemble washers on each side of the rod end. Install bolt (13) through the assembly and plate (12). Tighten the nut.7. With yellow LED (19) ON steady, adjust rod (15) to increase the length of the linkage (distance between rod ends) until green LED (20) just comes (turns) ON.8. Torque four jam nuts (17) to 14 4 N m (10 3 lb ft). Quick Check To See If Adjustments Are CorrectStart the

Caterpillar parts catalog:

Caterpillar parts catalog
3406E Marine Engine 9WR00001-UP


Parts aftercooler Caterpillar catalog:

5P9855 AFTERCOOLER AND LINES
3408, 3408B, 631D, 633D, 637D, 639D, 768C, 769C, 771C, 834B, 836, PR-450
4L9446 AFTERCOOLER
D320A, D330A, D333A
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.