AVSPARE.COM
parts catalog

ARM-BAIL 3535195 - Caterpillar



3535195 ARM-BAIL Caterpillar parts 966H, 966K, 966M, 966M XE, 972H, 972K, 972M, 972M XE ARM
Rating:
86
Alternative (cross code) number:
CA3535195
353-5195
3535195
Caterpillar 3535195 ARM-BAIL
Weight: 4 pounds 2 kg.

Buy ARM-BAIL 3535195 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3535195:

WHEEL LOADER  966H   966K   966M   966M XE   972H   972K   972M   972M XE   Caterpillar
Number on catalog scheme: 7
 
  For full view, you need register

Information:


Illustration 1 g01541733
Connections of the CAN Data LinkThis diagnostic code is recorded when the Machine ECM stops receiving information on the CAN Data Link.Note: The resistance of the wires for the CAN Data Link should measure approximately 60 ohms between circuit components.The possible causes of the diagnostic code are listed below:
A short has occurred in the machine harness.
A connector on the harness connector has been damaged.
An open connection exists in the 30 amp fuse for the Engine ECM.
An open exists in the machine harness.Test Step 1. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect all harness connections that are related to the CAN Data Link. Make sure that the connectors are clean and tight.
Check the connectors for proper mating. Ensure that all the seals are present and in place.
Check the harness for signs of damage or abrasion.
Check the wires at the connector. Ensure that the wires are secured tightly into the connector. Take care not to pull the wire out of the connector.
Check the exposed wires at the connectors for nicks or signs of abrasion.
Check for moisture inside the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and each socket of the machine harness connectors. Ensure that the contacts are properly installed. The contacts should mate correctly when the two pieces of the connector are placed together. Expected Result:The machine harness connectors are tight and free of corrosion. Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to Test Step 3.
NOT OK - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 2. CHECK THE CONTINUITY OF THE FUSE FOR THE MACHINE ECM
The disconnect switch remains in the OFF position.
Remove the 30 amp fuse for the Engine ECM from the fuse panel. The fuse is located under the "loader" joystick. Locate the plastic panel that is secured by two Torx screws under the "loader" joystick.
Place the leads of a digital multimeter across the contacts of the fuse. Set the meter to read ohms and note the measurement.Expected Result:The resistance of the fuse is less than 5 ohms.Results:
OK - The resistance of the fuse is less than 5 ohms. The fuse is correct. Proceed to Test Step 3.
NOT OK - The resistance of the fuse is more than 5 ohms. Repair: Replace the fuse. Ensure that the fix has corrected the problem.STOPTest Step 3. CHECK FOR SHORTS TO GROUND
The disconnect switch remains in the OFF position.
Disconnect the machine harness connectors from all electronic control modules that use the CAN Data Link.
At the machine harness for the Machine ECM, measure the resistance between frame ground and connector contacts J2-67 (wire F711-GN) and J2-68 (wire F712-GY) of the data link circuit. Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to Test Step 4.
NOT OK - The resistance is less than 5000 ohms. The machine

Cat SIS web machinery list:

Caterpillar parts catalog
966M Wheel Loader MD700001-UP (MACHINE) POWERED BY C9.3 Engine
966M XE Wheel Loader DZL00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader WGN00001-UP (MACHINE) POWERED BY C9.3 Engine
972M XE Wheel Loader R1Z00001-UP (MACHINE) POWERED BY C9.3 Engine
966H Wheel Loader Military RWE00001-UP (MACHINE) POWERED BY C11 Engine
950L Wheel Loader LXX00001-UP (MACHINE) POWERED BY C7.1 Engine
966L Wheel Loader FRS00001-UP (MACHINE) POWERED BY C9 Engine
972L Wheel Loader RFB00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader L8E00001-UP (MACHINE) POWERED BY C9.3 Engine
966M XE Wheel Loader B8P00001-UP (MACHINE) POWERED BY C9.3 Engine
972M XE Wheel Loader M5S00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader LMM00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader GGN00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader EJA00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader LSJ00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader M8W00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader L8R00001-UP (MACHINE) POWERED BY C9.3 Engine
966L Wheel Loader FSL00001-UP (MACHINE) POWERED BY C9.3 Engine
972L Wheel Loader YJW00001-UP (MACHINE) POWERED BY C9.3 Engine
966M XE Wheel Loader FL200001-UP (MACHINE) POWERED BY C9.3 Engine
972M XE Wheel Loader L9S00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader GMS00001-UP (MACHINE) POWERED BY C9.3 Engine
966M XE Wheel Loader XCR00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader A7800001-UP (MACHINE) POWERED BY C9.3 Engine
972M XE Wheel Loader AN300001-UP (MACHINE) POWERED BY C9.3 Engine
966H Wheel Loader A6D00001-UP (MACHINE) POWERED BY C11 Engine
972H Wheel Loader A7D00001-UP (MACHINE) POWERED BY C13 Engine
966H Wheel Loader A6G00001-UP (MACHINE) POWERED BY C11 Engine
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine
966H Wheel Loader Military FMW00001-UP (MACHINE) POWERED BY C11 Engine
966H Wheel Loader TAL00001-UP (MACHINE) POWERED BY C11 Engine
972H Wheel Loader GTA00001-UP (MACHINE) POWERED BY C13 Engine
966H Wheel Loader RYF00001-UP (MACHINE) POWERED BY C11 Engine
966K Wheel Loader TFS00001-UP (MACHINE) POWERED BY C9.3 Engine
972K Wheel Loader Z4W00001-UP (MACHINE) POWERED BY C9.3 Engine
966K Wheel Loader PBG00001-UP (MACHINE) POWERED BY C9.3 Engine
972K Wheel Loader PEM00001-UP (MACHINE) POWERED BY C9.3 Engine
972H Wheel Loader LCC00001-UP (MACHINE) POWERED BY C13 Engine
966K Series XE Wheel Loader NGX00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader A8P00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader KJP00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader DYC00001-UP (MACHINE) POWERED BY C9.3 Engine
966H Wheel Loader BJ600001-UP (MACHINE) POWERED BY C11 Engine
972H Wheel Loader WXZ00001-UP (MACHINE) POWERED BY C13 Engine
966M XE Wheel Loader P6C00001-UP (MACHINE) POWERED BY C9.3 Engine
972M XE Wheel Loader EDW00001-UP (MACHINE) POWERED BY C9.3 Engine
966H WHEEL LOADER A6J01801-UP (MACHINE) POWERED BY C11
972H WHEEL LOADER A7J00501-UP (MACHINE) POWERED BY C13
966H WHEEL LOADER A6J00001-01800 (MACHINE) POWERED BY C11 ENGINE
972H WHEEL LOADER A7J00001-00500 (MACHINE) POWERED BY C13 ENGINE


Parts arm Caterpillar catalog:

2147634 ARM GP-WINDOW WIPER
621H, 623H, 627H, 824G II, 824H, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G II, 980H, 988G, 98...
2147635 ARM GP-WINDOW WIPER
554, 564, 574B, 824G II, 824H, 824K, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834G, 834H, 834K, 836G, 836H, 836K, 844, 844H, 854G, 854K, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II,...
1545410 ARM-WINDOW WIPER
414E, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 426C, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 436C, 438C, 438D, 442D, 442E, 444E, 444F, 446D, 450E, 45...
3646457 ARM AS
950K, 962K, 966K, 972K, 980K, 980K HLG
3728071 ARM AS-MOUNTING
966M, 966M XE, 972M, 972M XE, 980M, 982M
3728072 ARM AS-MOUNTING
966M, 966M XE, 972M, 972M XE, 980M, 982M
3728073 ARM AS
966M, 966M XE, 972M, 972M XE, 980M, 982M
3728074 ARM AS
966M, 966M XE, 972M, 972M XE, 980M, 982M
3696008 ARM AS-LIFT
966M, 966M XE, 972M XE
3670096 ARM AS-LIFT
966H, 972G II, 972H
2374781 ARM AS-LIFT
966G II, 966H, 972G II, 972H
2105682 ARM AS
950G II, 950H, 962G II, 962H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.