AVSPARE.COM
parts catalog

ARM-SPRING LEF 4644964 - Caterpillar



4644964 ARM-SPRING LEF Caterpillar parts ARM
Rating:
21
Alternative (cross code) number:
CA4644964
464-4964
4644964
Caterpillar 4644964 ARM-SPRING LEF
Weight: 0.03 pounds 0 kg.

Buy ARM-SPRING LEF 4644964 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g02643297
Thumb rocker position sensor connectionsThis diagnostic code is associated with the Blade Control Handle Thumb Rocker Position Sensor. The FMI 08 diagnostic means that the ECM has determined that the signal frequency or the signal pulse width is not within the expected range.The possible causes of this condition are listed:
The signal circuit is shorted to the +battery circuit or shorted to ground intermittently.
The signal circuit is open intermittently or the sensor is disconnected.
The sensor may have failed.
The ECM may have failed. This is unlikely.Note: This diagnostic code is usually caused by an intermittent condition. The diagnostic code may be active for a period of time, then the diagnostic code may clear.Note: This procedure can cause new diagnostic codes to be recorded. Ignore these created diagnostic codes. When the procedure is completed, clear the created diagnostic codes.Test Step 1. CHECK FOR POWER AT THE SENSOR
Do not disconnect the 12 contact machine harness connector from the sensor.
At the back of the harness connector for the sensor, insert 7X-1710 Multimeter Probes along voltage supply contact "1" (wire 709-OR) and contact "2" (wire J764-BR).
Turn the key start switch and the disconnect switch to the ON position and measure the voltage.
Remove the multimeter probe from contact "2" (wire J764-BR) and measure the voltage from contact "1" (wire 709-OR) to frame ground.Expected Result:Both voltage measurements are approximately 10 DCV.Results:
OK - Both voltage measurements are approximately 10 DCV. Proceed to Test Step 2.
NOT OK - One or both voltage measurements is not approximately 10 DCV. There is a problem in the circuit. Repair: If both of the measurements are not approximately 10 V, the voltage supply wire 709-OR is open in the machine harness. Repair the machine harness or replace the machine harness.If the voltage check from contact "1" (wire 709-OR) to frame ground measures approximately 10 V and the contact "1" to contact "2" voltage check does not, the return circuit J764-BR is open in the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT OF THE SENSOR
Turn the key start switch and the disconnect switch to the OFF position.
At the back of the harness connector for the sensor, insert the 7X-1710 Multimeter Probes along the ground contact "2" (wire J764-BR) and the signal contact "3" (wire K757-YL).
Turn the disconnect switch and the key start switch to the ON position.
Monitor the signal of the sensor with the 146-4080 Digital Multimeter .
With the thumb rocker in the center position, record the duty cycle percentage value. Slowly depress the left-hand side of the thumb rocker and slowly depress the right-hand side of the thumb rocker. Record the high and the low duty cycle values.Expected Result:With the handle in the center position, the duty cycle should be approximately 50 percent. The high value should be approximately 80 5 percent and the low value should be approximately 20 5 percent. The values should have increased or decreased at a steady rate through the duty cycle range as


Parts arm Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.