9W0408 AXLE GP-POWER TRAIN Caterpillar parts D11N, D11R AXLE
Rating:
Alternative (cross code) number:
CA9W0408
9W-0408
9W0408
CA9W0408
9W-0408
9W0408
Weight: 0.22 pounds 0 kg.
Buy AXLE GP-POWER TRAIN 9W0408 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,
Information:
Implement ECM
The following is a list of Diagnostic Trouble Codes (DTCs) that are associated with the parameter circuits of the machine.
Table 1
Implement ECM (MID 82)
DTC Description System Response
268-2 Programmed Parameter Fault: Data Erratic, Intermittent, or Incorrect The Implement ECM has determined that a configuration parameter is not programmed. The ECM will display the parameter causing the problem via Cat® ET.
2183-13 Payload Monitoring System: Out of Calibration System must be calibrated before operating. The Cat Production Measurement is an electronic system that provides an accurate weight of the material that is loaded by the machine. The Cat Production Measurement system is controlled by the Implement ECM. The Cat Production Measurement operator commands to the Monitoring System Display are communicated via the Cat Data Link and J1939 datalink. The Implement ECM will then act on the command accordingly.Possible causes for an FMI 2 Diagnostic code are:
A configuration parameter on the ECM is blank or invalid.Possible causes for an FMI 13 Diagnostic code are:
The Implement ECM has never been calibrated.
The Implement ECM has lost all the permanent information on the setup of the machine.
Illustration 1 g03641999
Schematic of the Parameter circuits
Note: The diagram above is a simplified schematic of the connections for the parameter circuits. The schematic is electrically correct. However, not all the possible harness connectors are shown. Refer to the latest revision of the Electrical Schematic for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active before performing a troubleshooting procedure. For sensors powered via the fuse panel, check the condition of the appropriate fuse before beginning the troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Identify The Active DTC Code Associated With The Suspect Circuit
Code present. FMI 2 diagnostic code, proceed to Test Step 2.
FMI 13 diagnostic code, proceed to Test Step 4.
Begin Process For FMI 2 Troubleshooting HERE
2. Verify The Configuration Of The Sales Model
A. Use the Caterpillar Electronic Technician (Cat ET) to verify that the ECM is configured to the default setting configuration.
The ECM has been configured correctly to the default setting configuration. OK - The ECM has been configured correctly to the default setting configuration.
Repair:Verify that the
The following is a list of Diagnostic Trouble Codes (DTCs) that are associated with the parameter circuits of the machine.
Table 1
Implement ECM (MID 82)
DTC Description System Response
268-2 Programmed Parameter Fault: Data Erratic, Intermittent, or Incorrect The Implement ECM has determined that a configuration parameter is not programmed. The ECM will display the parameter causing the problem via Cat® ET.
2183-13 Payload Monitoring System: Out of Calibration System must be calibrated before operating. The Cat Production Measurement is an electronic system that provides an accurate weight of the material that is loaded by the machine. The Cat Production Measurement system is controlled by the Implement ECM. The Cat Production Measurement operator commands to the Monitoring System Display are communicated via the Cat Data Link and J1939 datalink. The Implement ECM will then act on the command accordingly.Possible causes for an FMI 2 Diagnostic code are:
A configuration parameter on the ECM is blank or invalid.Possible causes for an FMI 13 Diagnostic code are:
The Implement ECM has never been calibrated.
The Implement ECM has lost all the permanent information on the setup of the machine.
Illustration 1 g03641999
Schematic of the Parameter circuits
Note: The diagram above is a simplified schematic of the connections for the parameter circuits. The schematic is electrically correct. However, not all the possible harness connectors are shown. Refer to the latest revision of the Electrical Schematic for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active before performing a troubleshooting procedure. For sensors powered via the fuse panel, check the condition of the appropriate fuse before beginning the troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Identify The Active DTC Code Associated With The Suspect Circuit
Code present. FMI 2 diagnostic code, proceed to Test Step 2.
FMI 13 diagnostic code, proceed to Test Step 4.
Begin Process For FMI 2 Troubleshooting HERE
2. Verify The Configuration Of The Sales Model
A. Use the Caterpillar Electronic Technician (Cat ET) to verify that the ECM is configured to the default setting configuration.
The ECM has been configured correctly to the default setting configuration. OK - The ECM has been configured correctly to the default setting configuration.
Repair:Verify that the
Caterpillar SIS machinery equipment:
Caterpillar SIS
- D11N TRACTOR / POWER SHIFT / 74Z00001-UP (MACHINE) POWERED BY 3508 ENGINE » 9W-0408 AXLE GP-POWER TRAIN
- D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY 3508 Engine » 9W-0408 AXLE GP
- D11R Track-Type Tractor Power Shift 8ZR00001-UP (MACHINE) POWERED BY 3508 Engine » 9W-0408 AXLE GP
Caterpillar parts catalog:
Parts axle Caterpillar catalog:
6W9663
AXLE AR-REAR
FB518
FB518
9C1980
AXLE AR-FLOTATION
245, FB518
245, FB518
7V0048
AXLE AR-FRONT
613C, 613C II
613C, 613C II
6W2565
AXLE AR-FRONT
518, FB518
518, FB518
9U4812
AXLE GP-OSCILLATING
825C, 826C
825C, 826C
9R5224
AXLE AS-REAR
416, 426
416, 426