AVSPARE.COM
parts catalog

BALL 0005610 - Caterpillar



0005610 BALL Caterpillar parts BALL
Rating:
36
Alternative (cross code) number:
CA0005610
000-5610
0005610
Caterpillar 0005610 BALL
Weight: 0.04 pounds 0 kg.

Buy BALL 0005610 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Removal Procedure
Start By:
Remove the winch, if equipped. Refer to Disassembly and Assembly, RENR5543, "Winch - Remove".
Remove the ripper assembly, if equipped. Refer to Disassembly and Assembly, "Ripper - Remove". Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.Note: Put location marks and marks for the purpose of orientation on all fittings.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Drain the hydraulic oil from the hydraulic tank into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the proper procedure. Note: Step 2 is not required if a winch is removed.
Illustration 1 g00824822
Remove plate (1).
Illustration 2 g00822731
Remove rear bottom guard (2) in order to gain access to the track drive motors through the bottom of the machine.
Illustration 3 g00824797
Illustration 4 g00825884
Open the access door on the left side of the machine. Loosen the hose clamps and remove hose (6) that is installed above the batteries.
Remove bolts (3) from the inside of left enclosure (5). Remove bolts (4) and remove left enclosure (5).
Remove the batteries. Refer to Operation and Maintenance Manual, "Battery or Battery Cable - Inspect/Replace".
Illustration 5 g01050960
Illustration 5 is from the rear of the machine.
Disconnect harness assembly (7) on left track drive motor (14).
Repeat Step 7 for harness assembly (7) on right track drive motor (17).
Disconnect tube assembly (8) from the tee that is above left track motor (14).
Remove tube assembly (9).
Remove hose assembly (12) at two locations.
Disconnect tube assembly (11) from left track drive motor (14).
Disconnect harness assembly (15).
Remove speed sensor (13).
Repeat Step 13 and Step 14 for the right track motor.
Disconnect tube assembly (10) from the right parking brake.
Disconnect hose assemblies (16) from both track drive motors.
Illustration 6 g01051000
Illustration 6 is from the underside of the machine.
Disconnect tube assembly (11) from the tee and remove tube assembly (11) from the machine.
Disconnect tube assembly (21) from the tee.
Disconnect hose assembly (19) from the right parking brake.
Disconnect hose assemblies (18) from both track drive motors.
Disconnect tube assembly (8) from fitting (20) and remove tube assembly (8) from the machine.
Remove fitting (20) from left track drive motor (14).
Illustration 7 g01051007
Use a suitable lifting device in order to support left track drive motor (14). The weight of the track drive motor is approximately 47 kg (104 lb). Remove nuts (22).
Illustration 8 g01051011
Carefully lower left track drive motor (14) through the opening in the chassis.
Repeat Step 24 and Step 25 for the right track drive motor.


Parts ball Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.