AVSPARE.COM
parts catalog

BALL JOINT 1C4260 - Caterpillar



1C4260 BALL JOINT Caterpillar parts PR-1000 BALL
Rating:
10
Alternative (cross code) number:
CA1C4260
1C-4260
1C4260
Caterpillar 1C4260 BALL JOINT
Weight: 0.010 pounds 0 kg.

Buy BALL JOINT 1C4260 Caterpillar genuine, new aftermarket tractor parts with delivery
COLD PLANER,

Compatible equipment models: 1C4260:

COLD PLANER  PR-1000   Caterpillar
Number on catalog scheme: 28
 
  For full view, you need register

Information:


Table 5
FMI 6 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check The Solenoid
A. Turn the start switch and the disconnect switch OFF.
B. Disconnect the solenoid from the machine harness.
C. Turn the start switch and the disconnect switch ON. Do not start the engine.
D. Observe the status of the diagnostic code.
The FMI 6 changes to an FMI 5 after the solenoid is disconnected. OK - The circuit is correct. The solenoid has failed.
Repair: Repeat the test. Verify the solenoid failure. Replace the solenoid.
Proceed to Test Step 3.
NOT OK - The diagnostic code remains active.
Proceed to Test Step 2.
2. Check Machine Harness For A Short To Ground
A. The machine harness remains disconnected from the solenoid.
B. Turn the start switch and the disconnect switch OFF.
C. Disconnect the harness connectors from the ECM.
D. At the harness connector for the ECM, measure the resistance between the solenoid signal contact and all ground contacts.
Each reading is greater than 5K Ω. OK - Machine harness correct.
Proceed to Test Step 3.
NOT OK - One or more of the resistance measurements are less than 5 Ω. A short circuit exists in the machine harness.
Repair: A short circuit exists between the signal wire and the circuit with the low resistance. Repair or replace the machine harness.
Note: A resistance that is greater than 5 Ω but less than 5K Ω would indicate a loose connection or a corroded connection in the circuit. A resistance measurement that is greater than 5K Ω would indicate an open in the circuit.
Proceed to Test Step 3.
3. Check If The Diagnostic Code Remains
A. Reconnect all harness connectors. Return machine to normal operating condition.
B. Turn the start switch and the disconnect switch ON.
C. Clear all diagnostic codes.
D. Operate the machine.
E. Stop the machine and engage the safety.
F. Check if the diagnostic code is active.
The diagnostic code is no longer present. OK - The diagnostic code does not exist currently. The initial diagnostic code may have been caused by poor electrical connection or short at one of the harness connections. Resume machine operation.
STOP.
NOT OK - The diagnostic trouble code has not been corrected. If the diagnostic code has not been corrected after performing the procedure a second time, the ECM may require replacement.
Prior to replacing the ECM, always contact the Technical Communicator at your dealership for possible consultation with Caterpillar. This consultation may effect repair time.
Follow the steps in Troubleshooting, "ECM - Replace" if the ECM needs to be replaced.
STOP.
Table 6
FMI 7 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check For Diagnostic Codes Related To Solenoids
A. Check for diagnostic codes of that are related to solenoid failures.
The solenoids are

Caterpillar parts catalog:

Caterpillar parts catalog
PR-1000 PAVEMENT PROFILER 5XC00001-00137 (MACHINE) POWERED BY 3208,3412 ENGINE


Parts ball Caterpillar catalog:

0780652 BALL
CP-433B, CS-431B, CS-551
8T6284 BALL BEARING
PR-1000, PR-450
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.