AVSPARE.COM
parts catalog

BAR-SLIDE 4646152 - Caterpillar



4646152 BAR-SLIDE Caterpillar parts BAR
Rating:
31
Alternative (cross code) number:
CA4646152
464-6152
4646152
Caterpillar 4646152 BAR-SLIDE
Weight: 0.42 pounds 0 kg.

Buy BAR-SLIDE 4646152 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:

TYPE="1" START="1">
Check for the proper version of the regulator.
Check the part number of the digital voltage regulator. Refer to the chart in Testing And Adjusting, "Troubleshooting". Check whether the digital voltage regulator is proper for the application.Expected Result: The digital voltage regulator is proper for the application.Results:
OK: Go to Step 2.
NOT OK: Install the proper digital voltage regulator. STOP.
Check the status of the display.
Stop the generator set.
Observe the display on the digital voltage regulator.Expected Result: The display should contain a number.Results:
OK: Proceed to Step 4.
NOT OK: No number is present on the display. Proceed to Step 3.
Check the DC voltage.
Check for proper DC voltage from terminal "B+" to "B-". The acceptable voltage range is 18 VDC to 32 VDC.Expected Result: The sufficient DC voltage is present.Results:
OK: The sufficient DC voltage is present. Remove the DC power wires from terminals "B+" and "B-" for 30 seconds. Reconnect the DC power wires to the "B+" and "B-" terminals. If the regulator display is still blank, the regulator is faulty. Then, the regulator needs to be replaced. If this condition has occured, verify that the correct burden resistor or rheostat is connected between the droop current transformer and the regulator. If no resistor is present, the regulator was destroyed because of high current on the CT input. Refer to Testing And Adjusting, "Wiring Diagrams". STOP.
NOT OK: The sufficient DC voltage is not present. Repair the supply voltage wiring, fuses and circuit breakers as necessary. STOP.
Verify the proper configuration of the parameters.Pay particular attention to parameters :01, :02, and :30.
If the rated voltage, parameter :01 is increased, the output voltage will increase.
If the sensing transformer ratio, parameter :02 is decreased, the output voltage will increase.
If the voltage droop, parameter :30 is increased, the output voltage will decrease as the generator output current increases. Try the default value.
If generator type is set incorrectly, the regulator may operate constantly in the under frequency curve. Check parameter :50 and compare actual frequency to verify.
If the current transformer is installed or wired incorrectly (reverse polarity) and voltage gain (parameter :15) is greater than zero, the output voltage will decrease as the generator output current increases. Reverse the wires on terminal 5 and terminal 6.
Display the number in parameters :92, :93, and :95 (if present). A display of "0000" indicates no faults. If a fault code is present, see System Operation, "Parameters".Expected Result: The problem has been resolved.Results:
OK: The problem has been resolved. STOP.
NOT OK: The problem has not been resolved. Proceed to Step 5.
Check the PM inputs.
Turn the engine off.
Check that all of the digital voltage regulator connections are tight and properly made per the appropriate wiring diagram.
Check PM fuses (connecting to terminals 26 and 30 of the digital voltage regulator).
Restart the engine.
Check the PM inputs (26, 28, and 30) of the digital voltage regulator. Measure the AC voltage between terminals 26 to 28, 28 to 30, and 26 to 30.
If the digital voltage regulator is connected as a self-excited regulator, check if the power transformers

Caterpillar parts catalog:

Caterpillar parts catalog
MD6310 Rotary Blasthole Drill DLK00001-UP (MACHINE) POWERED BY C32 Engine
MD6310 Rotary Blasthole Drill DLZ00001-UP (MACHINE) POWERED BY C32 Engine


Parts bar Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.