AVSPARE.COM
parts catalog

BEARING 3599626 - Caterpillar



3599626 BEARING Caterpillar parts BEARING
Rating:
86
Alternative (cross code) number:
CA3599626
359-9626
3599626
Caterpillar 3599626 BEARING
Weight: 165 pounds 74 kg.

Buy BEARING 3599626 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

1. Disconnect two fuel lines (1) from the fuel transfer pump. 2. Remove oil line (3) and elbow (2). 3. Remove the two bolts that hold the fuel transfer pump in place. Remove fuel transfer pump (4) and gasket (5).Install Fuel Transfer Pump
1. Install fuel transfer pump (1) and gasket (2) on the engine. 2. Connect two oil lines (3) to the fuel transfer pump.Disassemble Fuel Transfer Pump
Start By:a. remove fuel transfer pump 1. Remove the two bolts and clamps that hold the service meter in position. Remove service meter (3) from the fuel transfer pump. Remove the O-ring seal from the service meter.2. Remove the bolts that hold body (1) to cover (2). Remove the cover from the body. 3. Remove plug (3), spring (5), and plunger (6) from cover (2). Remove seal (4) from plug (3). 4. Remove gear (7) from body (1). 5. Remove nut (8) and gear (9) from shaft (11). Remove the key from the shaft.6. Remove O-ring seal (10) and shaft (11) from body (1). 7. Use a press, as shown, to remove gear (12) from shaft (11). 8. Use tool (A) to remove bearing (13) from the end of body (1). Remove the two lip type seals that are behind bearing (13). 9. Remove dowel (14), ferrule (15), and valve assembly (17) from the body. Use tooling (B) to remove bearing (16).Assemble Fuel Transfer Pump
1. Install dowel (1) in the body so that the dowel is even with, or a maximum of 0.3 mm (.010 in) below surface (3).2. Install ferrule (2) in the body so the ferrule extends 5.6 mm (.22 in) above the surface. 3. Install valve assembly (4) in the body. Make sure the top of the valve assembly is approximately 0.4 mm (.015 inch) below the surface. Stake the valve assembly in three places to hold the valve assembly in place.4. Use tooling (A) to install bearing (5) in the body. Install the bearing so that the top of the bearing is 0.8 mm (.03 in) below the surface. 5. Use tooling (A) to install lip type seal (6) with the lip up, as shown. Install the seal so that dimension (X) is 24.6 mm (.97 in).6. Use tooling (A) to install lip type seal (7) with the lip down, as shown. Install the seal so that dimension (Y) is 14.2 mm (.56 in).7. Put clean diesel fuel on the lips of lip type seals (6) and (7).8. Use tooling (A) to install bearing (8) in the body. Install the bearing so that the bearing is even with the end of the body, as shown. 9. Heat gear (9) to a maximum temperature of 316°C (600°F). Install gear (9) on shaft (10) so that dimension (Z) is 49.7 mm (1.957 in). 10. Install O-ring seal (11) on the body. Put clean engine oil on the seal.11. Install shaft (10) and key (13). Install gear (12) and nut (14). Tighten nut (14) to a torque of 30


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.