AVSPARE.COM
parts catalog

BEARING, MAIN UPPER 7098515C1 - Caterpillar



7098515C1 BEARING, MAIN UPPER Caterpillar parts BEARING
Rating:
41
Alternative (cross code) number:
CA7098515C1
70985-15C1
7098515C1
Caterpillar 7098515C1 BEARING, MAIN UPPER

Buy BEARING, MAIN UPPER 7098515C1 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 5
 
  For full view, you need register

Information:


Illustration 9 g00930858
Illustration 10 g00930857
Position hose (16) and hose (17) to the front axle. Connect the hoses to the front axle.
Position harness (8) to the front axle. Install the cable strap that secures the harness to hose (16). Refer to the white arrow in Illustration 10 and to the note that was made during the removal procedure for the position of the cable strap.
Illustration 11 g00930859
Position hoses (15) to the hydrostatic drive motor before connecting the hoses to the hydrostatic drive motor.
Illustration 12 g00930860
Connect tee (10) and hose (13) to elbow (12) at connector (14) .
Illustration 13 g00930861
Connect hose (9) to tee (10) .
Tighten elbow (12) at connector (11) to the hydrostatic drive motor.
Illustration 14 g00930862
Position harness (5), harness (7) and harness (8) to the front axle. Connect harnesses (5) to harness (7) and harness (8) at electrical connectors (6) .
Illustration 15 g00930863
Connect electrical connector (4) to the hydrostatic drive motor.
Illustration 16 g00930864
Position hoses (3) to the hydrostatic drive motor before connecting the hoses to the hydrostatic drive motor.
Illustration 17 g00930865
Position hose (1) to the hydrostatic drive motor before connecting the hose to the hydrostatic drive motor.
Install a new cable strap in order to secure brake cable (2) to hose (1). Refer to the white arrow in Illustration 17 and to the note that was made during the removal procedure.
Illustration 18 g00930867
Use Tooling (A) to raise the wheels for the front axle off the ground no more than 50 mm (2 inch). The weight of the machine is approximately 5500 kg (12125 lb).
Illustration 19 g00930868
Remove Tool (B) and any cribbing that was used from the engine compartment at the right front side of the machine. Refer to Illustration 19.
Illustration 20 g00930871
Remove Tool (C) and any cribbing from the underside of the cab on the left front side of the machine. Refer to Illustration 20.
Use Tooling (A) to lower the machine to the ground before removing the Tooling from the machine.
Illustration 21 g00930872
Remove all the cribbing that was installed between the rear axle and the chassis in order to stop any oscillation of the rear axle. Refer to the white arrow in Illustration 21., End By:
Remove the boom cylinder lock and lower the boom. Refer to Operation and Maintenance Manual, "Boom Cylinder Lock - Removal and Installation Procedures".
Install the drive shaft. Refer to Disassembly and Assembly Manual, "Drive Shaft - Remove and Install".
Install the fenders onto both the front wheels. Refer to Disassembly and Assembly ManualRENR5162"Machine Systems", "Fender - Remove and Instal".


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.