AVSPARE.COM
parts catalog

BLADE AS. 9W0090 - Caterpillar



9W0090 BLADE AS. Caterpillar parts D9L BLADE
Rating:
68
Alternative (cross code) number:
CA9W0090
9W-0090
9W0090
Caterpillar 9W0090 BLADE AS.

Buy BLADE AS. 9W0090 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 9W0090:

TRACK-TYPE TRACTOR  D9L   Caterpillar
Number on catalog scheme: 6
 
  For full view, you need register

Information:


Table 1
Required Tools    
Part Number     Description     Quantity    
139-4166     Data Link Cable     1    
7X-1425     Cable     1    
4C-6805     Adapter     1    
171-4400     Communication Adapter Tool     1    The software program that will be used for this test procedure is the Caterpillar Electronic Technician (ET). The Caterpillar Electronic Technician is a software program that can be used on an IBM-compatible personal computer.ReferenceFor more information about the use of Electronic Technician, refer to Testing and Adjusting, "Using Caterpillar Electronic Technician (ET) to Determine Diagnostic Codes" for the machine that is being serviced.Machine Preparation
Park the machine on a smooth, level surface.
Shift the transmission direction control switch to the NEUTRAL position.
Lower the bucket or the work tool to the ground.
Engage the parking brake.
Place blocks in front of the wheels and behind the wheels.
Illustration 1 g00814825
Steering Frame Lock (1) Steering frame lock in LOCKED position
Install the steering frame lock.
Allow only authorized personnel on the machine. Keep unauthorized personnel off the machine and in clear sight of the operator.
Shut off the engine.Note: This calibration procedure can be performed without a running engine.
Turn the key start switch and the disconnect switch to the ON position.Procedure for Setting the Values of the Reduced Rimpull Selector Switch
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.Prevent possible injury by performing the procedure that follows before working on the machine.
Illustration 2 g00816040
Reduced rimpull selector switch (2) Position 1. (3) Position 2. (4) Position 3. (5) Position 4.
Illustration 3 g00815945
Location of service connector (6) Service connector. (7) 12 volt power source.
Connect the laptop computer to the service connector (6) in the cab. The service connector is located on the back wall of the cab to the right of the operator's station.Note: The Caterpillar Electronic Technician (ET) will allow a reduced rimpull setting at a lower position to be set to a value that is higher than the value of a reduced rimpull setting at a higher position. Make sure that the values of the reduced rimpull settings increase from the lowest setting to the highest setting.Note: The maximum reduced rimpull setting is 80%. The minimum reduced rimpull setting is 35%.
Open the software program (ET). Select the "Transmission 992G" from the "ECM Selector" menu.
Select the "Service" menu item from the toolbar. Select the "Configuration" menu item.
The reduced rimpull settings are near the bottom of the screen. Highlight the setting to change. Click on the "Change" button in the bottom left of the screen. Click the "Yes" button.
Enter the new value for the reduced rimpull setting. Click the "OK" button.
The value of the reduced rimpull setting for the "Position 1" switch has been changed.
Repeat Steps 2 through 6 for each of the reduced rimpull switches that require a change.
Close the software program (ET). Shut down the laptop computer. Disconnect the computer from the service connector in the cab.

Caterpillar parts catalog:

Caterpillar parts catalog
D9L TRACTOR 14Y00001-UP (MACHINE) POWERED BY 3412 ENGINE


Parts blade Caterpillar catalog:

6V5849 BLADE AS-WIPER
120H, 120H ES, 120H NA, 120M, 120M 2, 12H, 12H ES, 12H NA, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H, 163H NA, 16H, ...
6V5851 BLADE AS-WIPER
120G, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16M, 24H, 24M, 525B, 535B, 545, 583T, 587R, 587T, ...
6V5853 BLADE AS-WIPER
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.