AVSPARE.COM
parts catalog

BLOCK 1246143 - Caterpillar



1246143 BLOCK Caterpillar parts 30/30, DEUCE BLOCK
Rating:
85
Alternative (cross code) number:
CA1246143
124-6143
1246143
Caterpillar 1246143 BLOCK
Weight: 2 pounds 1 kg.

Buy BLOCK 1246143 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 1246143:

TRACK-TYPE TRACTOR  30/30   DEUCE   Caterpillar
Number on catalog scheme: 16
 
  For full view, you need register

Information:

MID 027 - CID 1283 - FMI 04
Illustration 1 g01406960
Schematic of the hoist control position sensorThis diagnostic code is associated with the hoist control position sensor. This diagnostic code is recorded when the Power Train/Chassis Electronic Control Module (ECM) reads the signal voltage of the sensor as being too low. The possible causes of this diagnostic code are listed:
Wire M997-PU is shorted to ground.
The sensor has failed.
The ECM may have failed.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1283 FMI 04 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.EJECTOR BODY. The status of the hoist control position sensor is unknown. The ejector system is unable to eject or retract the ejector plate. The gear of the machine is limited. The gear is limited to the current setting for the gear limit function. The ejector system will remain in the hold position until the hoist control lever is returned to the HOLD position. The ejector system will operate correctly after the diagnostic code has been corrected.Test Step 1. CHECK THE SENSORA. Turn the battery disconnect switch and the key start switch to the ON position.B. Ensure that the diagnostic code is active.C. Observe the status of the diagnostic code. Then, disconnect the machine harness from the sensor.Expected Result:The diagnostic code will remain active if the sensor is not the cause of the diagnostic code. The sensor is the cause of the diagnostic code if the diagnostic code is no longer active.Results:. YES – The diagnostic code remains active. The sensor is not faulty. The machine harness may be faulty or the ECM may be faulty. Proceed to Test Step 2.. NO – The diagnostic code is no longer active.Repair: The machine harness and the ECM are operating properly. The sensor is faulty. Replace the sensor.STOP.Test Step 2. CHECK THE SIGNAL CIRCUIT FOR A SHORT TO GROUND A. The sensor remains disconnected from the machine harness.B. Turn the key start switch and the battery disconnect switch to the OFF position.C. Disconnect the machine harness connector J1 and J2 from the ECM.D. At the J1 and J2 machine harness connectors, measure the resistance from contact J2-15 (M997-PU) to all source of frame ground.Expected Result:The resistance should be greater than 5 ohms.Results:. YES – The resistance is greater than 5 ohms. The machine harness is correct. Proceed to Test Step 3.. NO – The resistance is less than 5 ohms.Repair: There is a short in the machine harness. The short is between the signal circuit (wire M997-PU) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOP.Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS A. Inspect the contacts of the harness connectors and clean the harness connectors.B. The battery disconnect switch and the key start switch remain in the

Caterpillar parts catalog:

Caterpillar parts catalog
DEUCE Engineer Support Tractor 7RR00001-UP (MACHINE) POWERED BY 3126 Engine
30-30 Engineer Support Tractor 9XW00001-UP (MACHINE) POWERED BY 3126 Engine


Parts block Caterpillar catalog:

1175993 BLOCK
30/30, AD30, D250E, D250E II, D300E, D300E II, D350E, D350E II, D400E, DEUCE
1270813 BLOCK
30/30, AD30, D250E, D250E II, D300E, D300E II, D350E, D350E II, D400E, DEUCE
3911322 BLOCK AS-JUNCTION
24M, 30/30, 312D, 312D2, 312D2 GC, 313D, 313D2, 315D L, 318D L, 318D2 L, 374F L, 5110B, 5230B, 589, 730, 773E, 785C, 785D, 789D, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 797F, 986H, AP-655C, D10N, D6T...
1805617 BLOCK-CONTACT
30/30, AP-1000B, AP-1055B, AP-1055D, AP-655C, AP-800C, AP-900B, BG-225B, BG-2455C, BG-2455D, BG-245C, BG-260D, CB-214D, CB-334D, CB-334E, CB-335D, CB-434C, CB-434D, CB-534C, CB-534D, CB-535B, CB-634C,...
1166565 BLOCK AS
30/30, AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, AS4251C, AS4252C, BG-225B, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, ...
1958506 BLOCK-VALVE
30/30, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, D250E, D300E, DEUCE
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.