AVSPARE.COM
parts catalog

BLOCK 3534504 - Caterpillar



3534504 BLOCK Caterpillar parts 950H, 962H BLOCK
Rating:
46
Alternative (cross code) number:
CA3534504
353-4504
3534504
Caterpillar 3534504 BLOCK

Buy BLOCK 3534504 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3534504:

WHEEL LOADER  950H   962H   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:

Machine Dimension and Calibration Troubleshooting
Verify the Arm Sensor Calibrations
Perform the following in order to verify the "Arm Sensor Calibrations":
Start the display in "Service" mode. Press the "OK" key and hold the"OK" key when the display is powered up.
Select the "Setup Menu". Press "Configuration".
Use the up arrow key or the down arrow key in order to select "Diagnostics".
Press the button in order to select "Arm Sensors". A screen similar to Illustration 20 appears.
Illustration 20 g01357787
Place the machine on level ground. Position the boom so that the boom pins are level with the ground. The boom sensor must be level with the ground. The "Boom Sensor Angle" should read approximately zero (0) degrees. If the "Boom Sensor Angle" does not read approximately zero (0) degrees, then check the boom sensor calibration.
Position the stick so that the stick pins are perpendicular to the ground. The stick sensor must be perpendicular to the ground. The "Stick Sensor Angle" should read approximately –90 degrees. If the "Stick Sensor Angle" does not read approximately –90 degrees, then check the stick sensor calibration.
Position the bucket so that the bucket linkage is level with the ground. The bucket sensor must be level with the ground. The "Bucket Sensor Angle" should read approximately zero (0) degrees. If the "Bucket Sensor Angle" does not read approximately zero (0) degrees, then check the bucket sensor calibration.
Place the machine on reasonably level ground. Record the "Pitch Sensor Angle". Rotate the machine cab 180 degrees. Note the "Pitch Sensor Angle" again. After rotating the machine cab 180 degrees, the "Pitch Sensor Angle" should be the negative value of the first angle that was recorded. For example, if the "Pitch Angle" was –3.1 degrees, then the "Pitch Angle" should read 3.1 degrees after rotating the machine cab 180 degrees. If the values are not correct, then the pitch sensor calibration must be performed again.
If the optional tilt bucket kit was installed, then position the tilt bucket so that the tilt bucket is level with the ground. The tilt sensor should also be level with the ground. The "Tilt Bucket Sensor Angle" should read approximately zero (0) degrees. If the "Tilt Bucket Sensor Angle" does not read approximately zero (0) degrees, check the tilt bucket sensor calibration or the tilt bucket sensor mounting.Verify the Arm Positions (GPS measurements)
Perform the following steps in order to verify the arm positions, that is the GPS measurements.
Start the display in service mode. Press the "OK" key and hold the "OK" key when the display is powered up.
Press the display button in order to select Setup Menu. Press the display button in order to select "Configuration".
Use the up arrow key or the down arrow key in order to select "Diagnostics".
Press the display button in order to select "Arm Positions".
Illustration 21 g01357785
Place the machine on level ground with an orientation of 0 degrees (North). Install the boom bin center finder. Install the range pole target in the boom pin center finder. Place a "Rover" GPS receiver and bipod in the range

Caterpillar parts catalog:

Caterpillar parts catalog
302-7848 WASTE AR CUSTOM PRODUCT SUPPORT LITERATURE FOR 950H AND THE 962H WHEEL LOADERS K5K00001-UP (MACHINE)
WASTE AR CUSTOM PRODUCT SUPPORT LITERATURE FOR 950H WHEEL LOADER N1A00001-UP (MACHINE)
950H Wheel Loader N1A00001-UP (MACHINE) POWERED BY C7 Engine
962H Wheel Loader N4A00001-UP (MACHINE) POWERED BY C7 Engine
950H Wheel Loader K5K00001-UP (MACHINE) POWERED BY C7 Engine
962H Wheel Loader K6K00001-UP (MACHINE) POWERED BY C7 Engine
950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine
962H Wheel Loader M3G00001-UP (MACHINE) POWERED BY C7 Engine
950H PhII Wheel Loader K5K01000-UP (MACHINE) POWERED BY C7 Engine
962H PhII Wheel Loader K6K01000-UP (MACHINE) POWERED BY C7 Engine


Parts block Caterpillar catalog:

1573491 BLOCK
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H
2691727 BLOCK
980G II, 980H
2159153 BLOCK
824G II, 824H, 826G, 826G II, 826H, 834H, 836G, 836H, 988H
3152038 BLOCK
950H, 950K, 962H, 966H, 966K, 972H, 972K, 980H, 980K
3032906 BLOCK
966H, 966K, 972H, 972K
3190774 BLOCK
966H, 966K, 972H, 972K
1297626 BLOCK
966H, 966K, 972H, 972K
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.