AVSPARE.COM
parts catalog

BLOCK 3534599 - Caterpillar



3534599 BLOCK Caterpillar parts BLOCK
Rating:
51
Alternative (cross code) number:
CA3534599
353-4599
3534599
Caterpillar 3534599 BLOCK
Weight: 0.83 pounds 0 kg.

Buy BLOCK 3534599 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Introduction
Use the following procedure in order to measure the case drain of the swing motor.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Required Tools
Illustration 1 g02155580
Tooling Group "D"
Table 2
Tool Item Qty Part Number Description
D D1 1 6V-7788 Flow Meter
5 to 60 L/min (2 to 15 US gpm)
D2 1 8C-6874 Connector
D3 1 6V-9746 O-Ring Seal
D4 1 124-1901 Permanent Coupling
D5 3 ft 122-6870 Bulk Hydraulic Hose
D6 1 124-2147 Permanent Coupling
D7 1 6V-8943 Reducer
D8 1 7J-9108 O-Ring Seal
D9 1 6V-8398 O-Ring Seal
D10 1 6V-8939 O-Ring Reducer
D11 1 6V-8555 Nut
F 1 311-1362 Vacuum Cap Machine Preparation
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "Hydraulic System Pressure - Release".
Attach 311-1362 Vacuum Cap onto the hydraulic tank. Attach an air supply hose onto the assembly. Apply 276 to 414 kPa (40 to 60 psi). This procedure will pull a vacuum on the hydraulic system.
Illustration 2 g02155562
Flow Meter Tool Layout
Tooling D
(1) Case drain hose
(2) Elbow
(3) Swing motor
(4) Swivel
Install the following tools in accordance with the flow meter tool layout. Refer to Illustration 2.
Disconnect case drain hose (1) from elbow (2).
Connect the flow meter assembly (D) between elbow (2) and case drain hose (1). Note: Correct orientation of the flow meter is necessary. The oil flows from swing motor (3) to swivel (4).
Remove 311-1362 Vacuum Cap.
Illustration 3 g03885764
Pilot manifold
(5) Solenoid valve for swing parking brake
(6) Connector
Disconnect connector (6) from solenoid valve (5) for the swing parking brake. Test Procedure
Start the engine.
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Reference: Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Place the hydraulic activation control lever in the UNLOCKED position.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Slowly move the swing joystick and make sure that the swing parking brake is activated.
Move the swing joystick for a full SWING RIGHT. Measure the case drain oil. Refer to Table 1.
Return the joystick to the NEUTRAL position.
Stop the engine.
Connect connector (6) to the solenoid valve (5) for the swing parking brake.
Repeat this test procedure three times in order to obtain three measurements. For each test procedure, swing the upper structure to a different position.
Connect connector (6) to the solenoid valve for the swing parking brake (5).


Parts block Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.