parts catalog

BOLT 63000080 - Caterpillar

63000080 BOLT Caterpillar parts CB-514, CB-614, CS-431, CS-433
Alternative (cross code) number:
Caterpillar 63000080 BOLT

Buy BOLT 63000080 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 63000080:

VIBRATORY COMPACTOR  CB-514   CB-614   CS-431   CS-433   Caterpillar
Number on catalog scheme: 17
  For full view, you need register


Illustration 1 g00891935
Schematic of the Solenoid Valve (Shear Open)This diagnostic code is associated with the solenoid valve (shear open). The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal. The possible causes of the diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1803 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active, the ECM will turn off the current to the failed solenoid.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J2-13 (wire T971-OR) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-13 (T971-OR) and the circuit that has a low resistance measurement. Repair: Repair the machine harness or replace the machine harness. Stop.Test Step 2. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 1803 FMI 03 is active.Expected Result:The CID 1803 FMI 03 is active.Results:
YES - The CID 1803 FMI 03 is active. The problem has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". Stop.
NO - The CID 1803 FMI 03 is not active. The problem does not exist at this time.Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation. Stop.

Caterpillar parts catalog:

Caterpillar parts catalog

Parts bolt Caterpillar catalog:

4M5281 BOLT
10 FT, 10-20B, 10B, 120G, 120H, 120H ES, 120H NA, 120K, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H N...
4L9337 BOLT
10 FT, 10B, 130G, 14E, 215B, 215C, 225, 225D, 227, 229, 229D, 231D, 235, 235B, 235C, 235D, 245, 245B, 245D, 277C, 277C2, 277D, 287C, 287C2, 287D, 297C, 307, 3114, 3116, 3126, 3126B, 3176C, 318C, 3196,...
0S1615 BOLT
1140, 1150, 1160, 117, 120G, 127, 12E, 12G, 130G, 140B, 14G, 16, 1673, 1673B, 1673C, 1674, 1676, 1693, 16G, 183B, 215, 215B, 225, 229, 231D, 235, 235B, 235C, 245, 3116, 3126B, 3150, 3160, 3176, 3176B,...
0S1566 BOLT
10S, 117, 118, 119, 120B, 120G, 128, 129, 12E, 12F, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 140, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14E, 14G, 14H, 14H NA, 153, 16, 160G, 160H, 160H E...
4B0831 BOLT
3208, 3304, 3306, 3508, 3512, 3512B, 3512C, 3516, 3516B, 446, 446B, 508, 5230, 5230B, 578, 583R, 587R, 621E, 621F, 623B, 623E, 627F, 631E, 637E, 651E, 657E, 7155, 785, 789, 789D, 797, 797B, 814B, 815B...
7X0325 BOLT
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 14M, 160G,...
5H4893 BOLT
153, 163, 191, 215B, 225, 3192, 533, 543, 572R, 572R II, 583H, 587R, 587T, 65E, 7261, 75C, 75D, 75E, 769, 773, 793B, 85C, 85D, 85E, 950, 955L, 95E, 980C, AD45, AE40 II, CB-614, D353C, D6H, D6H XL, D6H...
0S1624 BOLT
10S, 120B, 12G, 140B, 140G, 14G, 16, 1673C, 215, 215B, 227, 235, 235B, 245, 3208, 3306, 3306B, 3406B, 3406C, 3408C, 3508, 3508B, 3512, 3516, 3516B, 3608, 3612, 3616, 44, 527, 561C, 561D, 571G, 572G, 5...
7X0368 BOLT
10 FT, 10B, 120H, 12H NA, 140H NA, 215C, 227, 30/30, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 515, 517, 525, 527, 572R II, 615, 615C, 621F, 621H, 621K, 623E, 623F, 623H, 623K, 623K LRC, 627F, 62...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.