AVSPARE.COM
parts catalog

BOLT S15885 - Caterpillar



S15885 BOLT Caterpillar parts 3408 BOLT
Rating:
18
Alternative (cross code) number:
CAS15885
S1-5885
S15885
Caterpillar S15885 BOLT

Buy BOLT S15885 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: S15885:

TRUCK ENGINE  3408   Caterpillar
Number on catalog scheme: 6
 
  For full view, you need register

Information:


Personal injury can result from flame cutting or welding on painted areas.The effect of gasses from burned paint is a hazard to the person doing the cutting or welding.Do not flame cut or weld on painted areas.
Do not torch or weld on painted areas. The effect of gasses from burned paint is a danger to the person doing the cutting or welding.
Do not ground the welder to electrical components such as the ECM or sensors. Improper grounding can cause damage to the drive train bearings, hydraulic components, electrical components, and other components.Clamp the ground cable from the welder to the component that will be welded. Place the clamp as close as possible to the weld. This will help reduce the possibility of damage.
Before carrying out arc welding on the machine or on any equipment attached to the machine, disconnect all power and ground leads from the batteries in order to avoid possible damage to electronic components.
Required Parts
Table 1
Component List for Wear Plates
Item Qty Part Number Description Thickness [mm]
1 2 524-8420(1) Plate 10 mm (0.4 inch)
2 2 536-7717(1) Plate 8 mm (0.31 inch)
3 2 524-8421(2) Plate 10 mm (0.4 inch)
4 2 536-7718(2) Plate 8 mm (0.31 inch)
(1) For use with 239D and 249D machines
(2) For use with 259B3/D, 279C/C2/D, 289C/C2/D, 299C/D/DXHP/D2/D2XHPmachines
Illustration 1 g06280540
Front frame wear plate 524-8420 (1) and 536-7717 (2)
Illustration 2 g06280543
Front frame wear plate 524-8421 (3) and 536-7718 (4)
Installation Procedure
Illustration 3 g02728020
Measure the distance between the top of the inner rear frame (A) to the top of the outer front frame (B). If the distance (D) is greater than 10 mm (0.39 inch), then add plate to the bottom surface of front frame (C). Initial gap (D) will be approximately 2 mm (0.08 inch) for a new machine. Refer to Table1 for the correct plates to use per model and gap size.
Remove undercarriage from the machine. Refer to Disassembly and Assembly Manual, KENR8831, "Undercarriage – Remove". Pull the front frame from the main frame. Remove any paint and debris from the frame at the mounting location for the wear plates.
Illustration 4 g06280554
Front frame weld instructions
(3) Front frame wear plate 524-8421 Plate shown as example
(E) Plug weld holes and grind flush
(F) 23 mm (0.90 inch)
(G) Flush with end of bottom Plate
(H) Maintain weld profile below surface
Weld the wear plates onto the frame. Refer to Illustration 4 for welding instructions.
Allow the welds to cool slowly to ambient temperature.
Remove all debris from the welds and from the welded area.
Paint the welded areas.
Install undercarriage onto the machine. Refer to Disassembly and Assembly Manual, KENR8831, "Undercarriage – Install".

Caterpillar parts catalog:

Caterpillar parts catalog
3408 TRUCK ENGINE 28V00001-04749


Parts bolt Caterpillar catalog:

2G2695 BOLT
140G, 3408, D44B, D550B
5J0279 BOLT
117, 3208, 633, 633D, 633E, 639D, 641B, 651B, 657B, 666
0308539 BOLT-12 POINT HEAD
24H, 24M, 3408, 621E, 623E, 627B, 627E, 631E, 633E II, 637D, 637E, 651E, 657E, 834B, 834G, 834H, 836, 836G, 836H, 988B, 988F, 988F II, 988G, 988H, D350E, D350E II, D400, D400E, D4E, D4E SR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.