AVSPARE.COM
parts catalog

BOOM GP 4647425 - Caterpillar



4647425 BOOM GP Caterpillar parts BOOM
Rating:
21
Alternative (cross code) number:
CA4647425
464-7425
4647425
Caterpillar 4647425 BOOM GP

Buy BOOM GP 4647425 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Use the UP or DOWN arrow key to select either 0, 1, 2 or 4 Turbochargers. Press the "ENTER/ACK" key in order to save the selection.Note: For a G3508 engine with two turbochargers, two turbochargers must be selected as shown in Illustration 2. Press the "ENTER/ACK" key in order to save the selection.
Illustration 3 g01410953
"SAVED" will be displayed on the display screen.
Illustration 4 g01410971
Press the "SETUP" button one more time. The "TURBO CONFIG" screen will be displayed.
Use the UP arrow key to select the turbocharger to configure. Then use the DOWN arrow key to cycle through the options for the turbocharger number that is shown on the display screen. Use the DOWN arrow key in order to choose from the following options:
Turbine Inlet ("TI")
Turbine Outlet ("TO")
Both turbine inlet and turbine outlet ("TI&TO")Only the configured number of turbochargers will be displayed.
Press the "ENTER/ACK" key in order to save the selection and return to the "TURBO CONFIG" screen.Note: For a G3508 low emission engine with a NOX sensor, select "TI&TO" for turbocharger 1 as shown in Illustration 4.
Illustration 5 g01411000
Repeat steps 6 and 7 for turbocharger number 2. Again use the DOWN arrows in order to cycle through the options which are: "TI", "TO" and "TI&TO". Note: For a G3508 low emission engine with a NOX sensor, "TI" must be selected. Refer to Illustration 5.
Return to the monitoring screen by pressing the "ESC" key."SET ARM TEMP" - The average cylinder exhaust temperature must achieve the arming temperature before the scanner activates the start-up timer. The arming temperature can be set to any temperature within the range of the scanner. The range of the scanner is 0 to 850 °C (32 to 1562 °F). Use the following procedure to configure the arming temperature:
"SETPTS" key
Press the "SETPTS" key until "SET ARM TMP" is displayed.
Use the up arrow key or the down arrow key in order to select the desired temperature.Note: To exit this function without changing the setting, press the "ESC" key before you press the "ENTER/ACK" key.
Press the "ENTER/ACK" key in order to save the new selection."SET TIMER" - The start-up timer must elapse before the scanner can monitor the selected setpoints.Use the following procedure to set the timer:
"SETPTS" key
Press the "SETPTS" key until "SET TIMER" is displayed.
Use the up arrow key or the down arrow key in order to select the desired number of minutes.Note: To exit this function without changing the setting, press the "ESC" key before you press the "ENTER/ACK" key.
Press the "ENTER/ACK" key in order to save the new selection.Default Configuration
Note: Most of the default configurations that are programmed at the factory can be reprogrammed.Output Switches - The two output switches can be dedicated to any combination of setpoints. The default configuration is listed in Table 2. Each output switch can be configured to be normally open or normally closed. The default configuration is normally open. Each switch can also be configured for latching or nonlatching. The default configuration is nonlatching.Note: The scanner's filter will delay the reaction of the

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
TL1055C Telehandler KDE01628-UP (MACHINE) POWERED BY C4.4 Engine


Parts boom Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.