AVSPARE.COM
parts catalog

BRACE AS 3599616 - Caterpillar



3599616 BRACE AS Caterpillar parts CG137-08, CG137-12, G3408B, G3408C BRACE
Rating:
27
Alternative (cross code) number:
CA3599616
359-9616
3599616
Caterpillar 3599616 BRACE AS
Weight: 4 pounds 1 kg.

Buy BRACE AS 3599616 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: 3599616:

GAS ENGINE  CG137-08   CG137-12   G3408B   G3408C   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:

Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly clean the exterior of the component. This action will help to prevent dirt from entering the internal mechanism.
Illustration 1 g01433124
Remove lip seals (1) from power link (2).
Illustration 2 g01433125
Use Tooling (A) to remove sleeve bearing (3) from the open end of power link (2).
Illustration 3 g01433160
Remove lip seals (4) and sleeve bearings (5) from the closed end of power link (2).
Illustration 4 g01433127
Remove lip seals (6) from the bore for the idler link in the stick.
Illustration 5 g00698417
Attach a suitable lifting device to Tooling (B), as shown.
Use Tooling (B) to remove the sleeve bearing from the stick.
Use Tooling (B) to remove the sleeve bearing from the opposite side of the stick. Installation Procedure
Make sure that the bores in the power link and the bore in the stick are thoroughly clean and free of dirt and debris prior to the installation of the sleeve bearings. Note: Make sure that the bearings are installed in the bore so that the identification numbers of the bearings are facing outward.
Illustration 6 g03508458
Lower the temperature of sleeve bearings (5) that will be installed in the closed end of power link (2).
Use Tooling (D) to install sleeve bearings (5) in the closed end of power link (2). Install the sleeve bearings until Dimension (X) is achieved. Dimension (X) should equal 9.50 0.80 mm (0.374 0.032 inch).
Illustration 7 g03508463
Use Tooling (E) to install lip seal (4) in the closed end of power link (2). Install lip seals (4) with the sealing lip toward the outside of the bore. Install the lip seals below the outside surface of the power link.
Illustration 8 g03508464
Lower the temperature of sleeve bearings (3) that will be installed in the open end of power link (2).
Use Tooling (A) to install two sleeve bearings (3) in the open end of power link (2). Install the sleeve bearings until Dimension (Y) is achieved. Dimension (Y) should equal 9.73 0.20 mm (0.383 0.008 inch).
Illustration 9 g03508477
Use Tooling (E) to install lip seals (1) in power link (2). Install lip seals (1) with the sealing lip toward the outside of the bore. Install the lip seals below the outside surface of the power link.
Illustration 10 g03508496
Illustration 11 g03508498
View A-A
Lower the temperature of two sleeve bearings (7) that will be installed in the stick.
Use Tooling (B) to install sleeve bearings (7) in the stick. Install the sleeve bearings until Dimension (Z) is achieved. Dimension (Z) must be 9.50 0.80 mm (0.374 0.032 inch).
Illustration 12 g03508502
Use Tooling (E) in order to install lip seals (6) in the stick. Install the lip seals with the sealing lip toward the outside of the bore. Install the lip seals below the outside surface of the stick.
Apply a thin coat of Tooling (C) to all sleeve bearings.
Apply a thin coat of Tooling (C) to the sealing lip of all lip seals. End By:
Install the bucket control linkage.

Caterpillar parts catalog:

Caterpillar parts catalog
G3408 Low Emission Engine 6RJ00001-UP
G3408C Natural Gas Engine Low Emission BAZ00001-UP
CG137–12 Gas Engine WRX00001-UP
CG137–08 Gas Engine WWF00001-UP
CG137–12 Generator Set SC200001-UP
CG137-12 Generator Set FYR00001-UP
CG137-08 Generator Set FPL00001-UP
XG400 CG137–12 Power Module AL500001-UP


Parts brace Caterpillar catalog:

1W0074 BRACE
3408, 3408C, 3408E, 3412, 3412C, G3408, G3408B, G3408C, G3412
1130277 BRACE-AIR CLEANER
CG137-08, CG137-12, G3408, G3408B, G3408C, G3412
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.