AVSPARE.COM
parts catalog

BRACKET AS 1245959 - Caterpillar



1245959 BRACKET AS Caterpillar parts D250D BRACKET
Rating:
69
Alternative (cross code) number:
CA1245959
124-5959
1245959
Caterpillar 1245959 BRACKET AS
Weight: 29 pounds 13 kg.

Buy BRACKET AS 1245959 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK,

Compatible equipment models: 1245959:

ARTICULATED TRUCK  D250D   Caterpillar
Number on catalog scheme: 38
 
  For full view, you need register

Information:


Personal injury can result from hot oil spray and raised attachments.Make sure all attachments have been lowered, oil is cool and the pressure has been released from the hydraulic system before removing any components or lines.Do not allow hot oil or components to contact skin.
Do not check for leaks with your hands. Pin hole (very small) leaks can result in a high velocity oil stream that will be invisible close to the hose. This oil can penetrate the skin and cause personal injury. Use cardboard or paper to locate pin hole leaks.
Table 1
REQUIRED TOOLS    
Part Number    Part Description    Quantity    
6V-7788     Oil Flow Meter     1    
8C-6874     Connector     2    
6V-8943     Reducer Assembly     2    
7X-3165     Swivel Adapter     2    
6V-9746     O-Ring Seal     2    
7J-9108     O-Ring Seal     2    
2M-9780     O-Ring Seal     2    
153-2994     Fitting     1    
153-2995     Fitting     1    
9U-7400     Multitach Tool Group     1    Flow Meter Assembly
Illustration 1 g00990827
Apply 5P-3413 Pipe Sealant to the pipe threads of 8C-6874 Connector (7). Install connector (7) at each end of 6V-7788 Oil Flow Meter (8) .
Install 6V-9746 O-Ring Seal (6) onto the face of each connector.
Install 6V-8943 Reducer Assembly (5) onto each connector.
Install 7J-9108 O-Ring Seal (4) onto the face of each reducer assembly.
Install 7X-3165 Swivel Adapter (3) onto each reducer assembly.
Install 2M-9780 O-Ring Seal (2) onto each swivel adapter.
Install 153-2994 Fitting (1) onto the input side of the flow meter assembly.
Install 153-2995 Fitting (9) onto the output side of the flow meter assembly.Output Test for the Gerotor Motor
Install the auger onto the skid steer loader. Refer to Operation and Maintenance Manual, SEBU7749, "Work Tool Installation".
Illustration 2 g00990835
Connect flow meter assembly (4) to lower fitting (3) .
Connect hydraulic hose (5) to the flow meter assembly.Note: Do not route the hydraulic hoses through the hose guide on the skid steer loader or through the hose guide on the frame mounting bracket.
Connect hydraulic hose (2) to upper fitting (1) .
Illustration 3 g00990839
Typical example
Apply three 13 mm (0.5 inch) strips of reflective tape (8) on alternate flats of the output shaft (9) .
Mount photo tach (7) of the 9U-7400 Multitach Tool Group to the gearbox (6) .
Enter the host machine.
Fasten the seat belt and lower the armrest.
Start the host machine.
Place the auxiliary hydraulic control to the AUX 1 position and activate the continuous flow control.
Increase engine speed until the flow meter reads 38 L/min (10 US gpm).
Check the output rpm on the multitach. The reading should be approximately 43.3 4 rpm.If the output rpm is less than 39 rpm, there may be excessive leakage within the gerotor motor. Replace the gerotor motor.

Caterpillar parts catalog:

Caterpillar parts catalog
D20D & D250D ARTICULATED TRUCK 6NG00001-UP (MACHINE) POWERED BY 3116 ENGINE


Parts bracket Caterpillar catalog:

7U7236 BRACKET
D250D, D250E, D250E II, D300E, D300E II
7U2551 BRACKET-MIRROR
554, 574, D250D, D250E, D250E II, D25C, D25D, D300D, D300E, D300E II, D30C, D350C, D350E, D350E II, D35C, D35HP, D400, D400E, D400E II, D40D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.