AVSPARE.COM
parts catalog

BRACKET AS 1246175 - Caterpillar



1246175 BRACKET AS Caterpillar parts D350E, D400E BRACKET
Rating:
27
Alternative (cross code) number:
CA1246175
124-6175
1246175
Caterpillar 1246175 BRACKET AS
Weight: 35 pounds 16 kg.

Buy BRACKET AS 1246175 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK,

Compatible equipment models: 1246175:

ARTICULATED TRUCK  D350E   D400E   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Illustration 1 g01876560
Use only a hydraulic hammer that is recommended byCaterpillar. The use of a hydraulic hammer that is not recommended by Caterpillar could damage your machine. Consult your Caterpillar dealer for information on recommended hydraulic hammers.
Only use the hydraulic hammer to break rocks, concrete, and other hard objects. Before you start hydraulic hammer operation, place the machine on a level, stable surface.Before you start hydraulic hammer operation, close the front window. Caterpillar recommends the installation of a window guard on the front window for protection from flying debris.
In order to avoid structural damage to the host machine or the hydraulic hammer, comply with the following:Do not attempt to break rocks or concrete by burying the hammer tool completely into the rocks or concrete.Do not apply a prying force to the hammer tool in order to remove the hammer tool from the material.
Do not allow the hydraulic hammer to continuously operate at one location and for more than 15 seconds. Change the location of the hydraulic hammer and repeat the procedure. Failure to change the location of the hydraulic hammer could cause the hydraulic oil to overheat. Overheated hydraulic oil could cause damage to the accumulator.Stop the hydraulic hammer immediately if the jumper lines are pulsating violently. This indicates that the accumulator nitrogen charge is lost. Consult your Caterpillar dealer for the necessary repair.
Do not use the dropping force of the hydraulic hammer to break rocks or other hard objects. This could cause structural damage to the machine.Do not use the sides or back of the hydraulic hammer to move rocks or other hard objects. Doing this could cause damage not only to the hammer but to stick or boom cylinder.Do not operate the hydraulic hammer with any of the cylinders fully retracted or extended. Doing this could cause structural damage to the machine, resulting in reduced machine life.
Do not use the hydraulic hammer to lift an object.Do not operate the hydraulic hammer while the stick is vertical to the ground. This could allow the stick cylinder to vibrate excessively.Operate the attachment control levers carefully in order to keep the hydraulic hammer's tool from hitting the boom.Do not operate the hydraulic hammer under water unless the hydraulic hammer is properly equipped. Operating the hydraulic hammer under water could cause serious damage to the machine hydraulic system. Consult your Caterpillar dealer for information on underwater operation.Do not operate the hydraulic hammer with the upper structure sideways to the undercarriage. Before you start hydraulic hammer operation, place the upper structure in the recommended positions that are shown in illustration 2. Any other operating positions could make the machine unstable. Any other operating positions could place excessive loads on the undercarriage.Refer to the following for any additional questions about the operation and care of your Caterpillar hydraulic hammer: Operation and Maintenance Manual, SEBU7346, "Hydraulic Hammers", Operation and Maintenance Manual, HEPU9000, "Hydraulic Hammers" and Decal, SMEU7397, "Hammer Operation/Maintenance".
Illustration 2 g00101503
(1) Incorrect working position
(2) Correct working position
(3) Incorrect working position
(4) Correct working position

Caterpillar parts catalog:

Caterpillar parts catalog
D400E Articulated Truck 2YR00001-UP (MACHINE) POWERED BY 3406 Engine
D350E Articulated Truck 9LR00001-UP (MACHINE) POWERED BY 3406 Engine


Parts bracket Caterpillar catalog:

1412675 BRACKET
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824G, 825G, 826C, 826G, 980C, 980F, 980F II, 980G, D350E, D400E, D8N, D8R, D8R II, HT400, ...
9N0316 BRACKET
3406, 3406B, 3406C, 3406E, 3408, 3456, C-15, C-16, C15, C18, CX31-C15I, CX35-P800, D350E, D400E, D40D, TH35-C15I
1750070 BRACKET
120G, 12G, 130G, 140G, 16G, 515, 517, 525, 525B, 525C, 527, 535B, 535C, 545, 545C, 613C, 615C, 631E, 633E II, 637E, 651E, 657E, 814F, 814F II, 815F, 815F II, 816F, 816F II, 924F, 938F, 950F II, 953C, ...
5U9349 BRACKET
D350E, D400, D400E, D40D
7U5957 BRACKET AS
D25D, D350E, D400E, D40D
1259244 BRACKET
D350E, D400E, D40D
9X4725 BRACKET AS
D25D, D350E, D350E II, D400E, D400E II
7U6210 BRACKET AS-MOUNTING
D25D, D350E, D350E II, D400E, D400E II, D40D
7U5957 BRACKET AS
D25D, D350E, D400E, D40D
1156746 BRACKET AS
D350E, D400E, D40D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.