AVSPARE.COM
parts catalog

BRACKET AS 1694992 - Caterpillar



1694992 BRACKET AS Caterpillar parts G112, VPG-25 BRACKET
Rating:
76
Alternative (cross code) number:
CA1694992
169-4992
1694992
Caterpillar 1694992 BRACKET AS

Buy BRACKET AS 1694992 Caterpillar genuine, new aftermarket tractor parts with delivery
GRAPPLE-MECHANICAL,

Compatible equipment models: 1694992:

GRAPPLE-MECHANICAL  G112   VPG-25   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:

Start By:a. remove exhaust manifold The exhaust manifolds do not have to be removed unless all the cylinder head assemblies are to be removed.1. Drain the coolant from the cooling system.2. Shut off the fuel supply on the engine. 3. Remove fuel lines (2), thermocouple (1) and the fuel line manifold from the cylinder head assembly. 4. If equipped, disconnect hose assembly (4) from water manifold (3). Remove the bolts to remove a section of water manifold (3) and elbow (6) from the cylinder head assembly.5. Remove bracket (5) from the cylinder head assembly. Air inlet elbow (7) does not have to be removed from the cylinder head assembly, only the bolts that hold the elbow to the cylinder head assembly.6. Remove the bolts, and remove air inlet elbow (7) from the cylinder head assembly. 7. Remove the access cover from under the cylinder head assembly. Remove the bolt and cap (9) to disconnect rod assembly (8) from fuel control shaft (10).8. Remove the rocket shaft assemblies and push rods. See the topic, Remove Rocker Shaft Assemblies And Push Rods, for this procedure. 9. Remove bolts (14) to remove lever assembly (13) and rod assembly (8) as a unit from the cylinder head assembly. If the lower end of rod assembly (8) does not have enough clearance to be removed, use tool (A) to turn the flywheel until the lower end of rod assembly (8) can be removed between the camshaft and engine block.10. Remove the bolt and clamp (12) from the fuel injector.
Do not put a force on the fuel injection rack or cause damage to it when the injectors are removed.
11. Use a pry bar to loosen fuel injector (11). Remove fuel injector (11) from the cylinder head assembly. 12. Remove the bolts to remove valve cover base (15) and the gasket from the cylinder head assembly. 13. Fasten a hoist to cylinder head assembly (16) with tooling (B). Remove all of bolts (17) and (18) to remove cylinder head assembly (16) from the engine. The weight of the cylinder head assembly is 47 kg (105 lb). 14. Remove head gasket (19), the seals, the spacer plate and spacer plate gasket from the engine.Install Cylinder Head Assemblies
Thoroughly clean the spacer plate and bottom surface of the cylinder head assembly. A new spacer plate gasket must be installed when the cylinder head assembly is removed.1. Install the spacer plate gasket and spacer plate. See the topic, Install Spacer Plate. 2. Install head gasket (19) on the spacer plate. Do not use any adhesives.
Before installation of the cylinder head assembly make sure the 4D514 Plug at location (X) is installed.
3. Fasten a hoist to cylinder head assembly (16). Put the cylinder head assembly in position on the spacer plate. 4. Put 5P3931 Anti-Seize Compound on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in the following sequence:a. Tighten all of the bolts to a torque of 30 5

Caterpillar parts catalog:

Caterpillar parts catalog
G112 G115 G125 G140 Mechanical Grapple ADN00001-UP (MACHINE)
G112 G115 G125 G140 MECHANICAL GRAPPLE BNZ00001-UP (MACHINE)
VPG-25, VPG-35, VPG-45 and VPG-55 Mechanical Grapple CHK00001-UP (MACHINE)


Parts bracket Caterpillar catalog:

1694976 BRACKET GP-MOUNTING
G112, G320, MP15, P360, S305, VHC-30, VHS-50, VPG-25, VRG30, VT30, VT50
1791645 BRACKET GP-MOUNTING
G112, G320, MP15, P215, P360, S305, VHC-30, VHP-30, VHS-50, VPG-25, VRG30, VT30, VT50
1694968 BRACKET GP-MOUNTING
G112, G320, MP15, S305, S365B, VHS-50, VPG-25, VRG30, VT50
1693071 BRACKET GP-MOUNTING
G112, P115, S115, VPC-30, VPG-25, VPS-35
1695319 BRACKET AS
G112, G320, MP15, P215, P360, S305, VHC-30, VHP-30, VHS-50, VPG-25, VRG30, VT30, VT50
1695315 BRACKET AS
G112, G320, MP15, S305, VHS-50, VRG30, VT50
1890312 BRACKET AS
G112, MP15, S365B, VT50
2258719 BRACKET AS
G112, G315B, G325B, MP15, MP318, P215, P360, VHC-30, VHP-30, VPG-25, VRG-40/2, VT30
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.