AVSPARE.COM
parts catalog

BRACKET 2332980 - Caterpillar



2332980 BRACKET Caterpillar parts M313C, M315C, M316C, M318C, M318C MH, M322C BRACKET
Rating:
12
Alternative (cross code) number:
CA2332980
233-2980
2332980
Caterpillar 2332980 BRACKET
Weight: 0.06 pounds 0 kg.

Buy BRACKET 2332980 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEELED EXCAVATOR,

Compatible equipment models: 2332980:

WHEELED EXCAVATOR  M313C   M315C   M316C   M318C   M318C MH   M322C   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:


Place roller (15) in the groove of the roller guide plate. Position roller (15) by the slider of cable assembly (14) .
Insert pin (16) of bracket assembly (2) through the slot of the slider of cable assembly (14). Insert pin (16) through the bore of roller (15) .
Fasten bracket assembly (2) to the upper windshield with screws (6). Tighten screws (6) to a torque of 12 3 N m (8.8 2.2 lb ft).
Repeat Steps 4.a to 4.c for bracket assembly (3) .Note: Make sure that each bracket assembly is installed horizontally.
Install the lower rollers and the lower bracket assemblies to the upper windshield in the following manner.
Place roller (15) in the groove of the roller guide plate on the right side.
Insert pin (16) of bracket assembly (4) through the slot of the slider of cable assembly (14). Insert pin (16) through the bore of roller (15) .
Fasten bracket assembly (4) to the upper windshield with screws (6). Tighten screws (6) to a torque of 12 3 N m (8.8 2.2 lb ft).
Repeat Steps 5.a to 5.c for bracket assembly (5) .Note: Make sure that each bracket assembly is installed horizontally.
Turn the engine start switch to the ON position.Note: Do not start the engine.
Open the upper windshield. If the alarm sounds the windshield needs adjustment.
Illustration 10 g00501891
(6) Screw (17) Switch (18) Bracket assembly
The position of switch (17) needs adjustment. Switch (17) is located in the upper right rear of the cab. Adjust switch (17) forward in the following manner.
Close the upper windshield.
Loosen screw (6) and move bracket assembly (18) forward.
Tighten screw (6) to a torque of 12 3 N m (8.8 2.2 lb ft).
Check the windshield again. If the alarm sounds repeat Steps 8.a through 8.c.
Illustration 11 g00501924
Upper windshield in the closed position (19) Nut (20) Bracket (21) Bumper
Open the upper windshield and check the clearance between bumper (21) of the upper windshield frame and bracket (20). If there is any clearance between the bumper and the bracket adjust the position of the bumper in the following manner.
Move the lower side of the upper windshield against the left side stop.
Loosen nut (19) and unscrew bumper (21). When bumper (21) touches bracket (20) stop. The tip of the bumper should deform slightly.
Tighten nut (19) to a torque of 30 7 N m (22 5 lb ft).
Open and close the upper windshield. Check the clearance between bumper (21) and bracket (20). If there is any clearance between the bumper and the bracket repeat Steps 9.a through 9.c.
Illustration 12 g00501966
(C) Clearance (6) Screw (9) Upper windshield frame (22) Rubber stopper
Open the upper windshield. Check clearance (C) between upper windshield frame (9) and rubber stoppers (22). Clearance (C) should be less than 1 mm (0.04 inch). If the clearance is greater than 1 mm (0.04 inch) adjust the upper windshield in the following manner.
Close the upper windshield.
Loosen screws (6) from rubber stopper (22) on both sides.
Remove the shims from rubber stoppers (22) .
Tighten screws (6) .
Open the upper

Caterpillar parts catalog:

Caterpillar parts catalog
M318C Excavator BCZ00001-02000 (MACHINE) POWERED BY 3056 Engine
M316C Excavator BDX00001-02000 (MACHINE) POWERED BY 3056 Engine
M322C Excavator BDK00001-02000 (MACHINE) POWERED BY 3056 Engine
M315C EXCAVATOR BDM00001-02000 (MACHINE) POWERED BY 3054 Engine
M313C Excavator BDR00001-02000 (MACHINE) POWERED BY 3054 Engine
M322C Excavator BDY00001-02000 (MACHINE) POWERED BY 3056 Engine
M318C Material Handler BEB00001-02000 (MACHINE) POWERED BY 3056E Engine
M318C Excavator BCZ02001-UP (MACHINE) POWERED BY 3056E Engine
M316C Excavator BDX02001-UP (MACHINE) POWERED BY 3056E Engine
M322C Excavator BDK02001-UP (MACHINE) POWERED BY 3056E Engine
M315C Excavator BDM02001-UP (MACHINE) POWERED BY 3054E Engine
M313C Excavator BDR02001-UP (MACHINE) POWERED BY 3054E Engine
M322C Excavator BDY02001-UP (MACHINE) POWERED BY 3056E Engine
M318C Material Handler BEB02001-UP (MACHINE) POWERED BY 3056E Engine
M318C Excavator H2D00001-UP (MACHINE) POWERED BY 3056E Engine
M316C Excavator H2C00001-UP (MACHINE) POWERED BY 3056E Engine
M322C Excavator H2E00001-UP (MACHINE) POWERED BY 3056E Engine
M315C Excavator H2B00001-UP (MACHINE) POWERED BY 3054E Engine
M313C Excavator H2A00001-UP (MACHINE) POWERED BY 3054E Engine
M322C Excavator H2G00001-UP (MACHINE) POWERED BY 3056E Engine
M318C Excavator H2F00001-UP (MACHINE) POWERED BY 3056E Engine


Parts bracket Caterpillar catalog:

6I1206 BRACKET-SHAFT
212, 3054, 3054B, 3056, 3056E, 307, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 424D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 550B, 554, 560B, 564, 574B, 908...
2S2109 BRACKET
215, 225, 225D, 227, 229, 229D, 231D, 235, 235B, 235C, 235D, 561C, 561D, 571G, 572G, 583K, 594, 594H, 627E, 637E, 834, 834B, 836, 988B, 992, 992C, CB-214B, D10, D5, D5B, D6C, D6D, D6D SR, D7F, D7G, D8...
2494599 BRACKET AS
M316C, M316D, M318C, M318D
2518838 BRACKET AS
M316C, M316D, M318C, M318D
1887663 BRACKET AS
M322C, M322D, M322D MH
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.