AVSPARE.COM
parts catalog

BREATHER, ASSY 7098331C1 - Caterpillar



7098331C1 BREATHER, ASSY Caterpillar parts BREATHER
Rating:
16
Alternative (cross code) number:
CA7098331C1
70983-31C1
7098331C1
Caterpillar 7098331C1 BREATHER, ASSY

Buy BREATHER, ASSY 7098331C1 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Removal Procedure
Start By:
Turn the battery disconnect switch to the OFF position. Refer to Operation and Maintenance Manual, "Battery Disconnect Switch".
Put identification marks on all wires and all connectors for installation purposes.
Illustration 1 g00930278
Remove six bolts (2) in order to lower cab headliner (1) .
Illustration 2 g00930279
Disconnect harness (3) for dome light (4) and harness (5) for speakers (6) before removing cab headliner (1) from the cab.
Illustration 3 g00930326
Disconnect tube (7) for the windshield washer. Open cap (8) for wiper arm (9) and remove nut (10) before removing the wiper arm from the machine.
Illustration 4 g00930329
Illustration 5 g00930330
Disconnect electrical connector (11) for wiper motor (12). With the aid of a second person, support the wiper motor from the inside of the cab. At the same time remove nut (13), sealing washer (14), cap (15), nut (16), and sealing washer (17). Remove the wiper motor from the machine.Installation Procedure
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Illustration 6 g00930329
Illustration 7 g00930330
With the aid of a second person, position wiper motor (12) and install sealing washer (14), nut (13), sealing washer (17), nut (16) and cap (15). Tighten nut (16) to a torque of 7.5 .5 N m (5.5 0.4 lb ft). Connect electrical connector (11) .
Illustration 8 g00930279
Position cab headliner (1) in the cab in order to enable the connection of electrical connector (5) for speakers (6) and harness (3) for dome light (4) .
Illustration 9 g00930278
Lift cab headliner (1) into position and install six bolts (2) .
Use the following procedure to install the wiper arm:
If a new wiper motor has been installed disregard steps 5.b and 5.c.
Turn the battery disconnect switch to the ON position. Refer to Operation and Maintenance Manual, "Battery Disconnect Swithch.".
Turn the switch for the front window wiper to the ON position and then turn the switch for the front window wiper to the Off position. This will make sure that the wiper motor is in the PARK position. Refer to Operation and Maintenance Manual, "Window Wiper and Washer Control".
Illustration 10 g00930340
Illustration 11 g00930326
Position wiper arm (9) so that the wiper blade is in full contact with the front left side of the windshield. The wiper blade must be parallel with the edge of the windshield at a distance of 18 3 mm (0.71 0.12 inch). Note the black arrows on illustration 10. Install nut (10) and tighten the nut to a torque of 23 1 N m (17 0.7 lb ft).
Wait for at least thirty minutes. Do not wait for more than four hours. Tighten nuts (10) again to a torque of 23 1 N m (17 0.7 lb ft). Close cover (8) for the wiper arm.
Connect hose (7) for the window washer.

Caterpillar parts catalog:

Caterpillar parts catalog
CT11 ON HIGHWAY TRUCK ENGINE EBC00001-UP
CT13 SCR ON HIGHWAY TRUCK ENGINE JFB00001-UP
CT13 ON HIGHWAY TRUCK ENGINE KBK00001-UP


Parts breather Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.