AVSPARE.COM
parts catalog

BRKT-GREASE GU 1C3809 - Caterpillar



1C3809 BRKT-GREASE GU Caterpillar parts BRKT
Rating:
16
Alternative (cross code) number:
CA1C3809
1C-3809
1C3809
Caterpillar 1C3809 BRKT-GREASE GU
Weight: 0.26 pounds 0 kg.

Buy BRKT-GREASE GU 1C3809 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

General Torque Information
Mismatched or incorrect fasteners can result in damaged or malfunction, or possible injury.Take care to avoid mixing metric dimensioned fasteners and inch dimensioned fasteners.
Prior to installation of any hardware, ensure that components are in near new condition. Bolts and threads must not be worn or damaged. Threads must not have burrs or nicks. Hardware must be free of rust and corrosion. Clean the hardware with a noncorrosive cleaner. Do not lubricate the fastener threads except for the rust preventive. The rust preventive should be applied by the supplier of that component for purposes of shipping and storage. Other applications for lubricating components may also be specified in the Service Manual.For additional torque specifications, not included in this section, refer to Torque Specifications, SENR3130, available from your Caterpillar dealer.Standard Torque for Inch Fasteners
The following charts give general torques for bolts, nuts, and taperlock studs of SAE Grade 5 or better quality.
Inch Nuts and Bolts
Inch Taperlock Studs
Standard Torque for Metric Fasteners
Be very careful never to mix metric with U.S. customary (standard) fasteners. Mismatched or incorrect fasteners will cause machine damage or malfunction and can result in personal injury.Original fasteners removed from the machine should be saved for reassembly whenever possible. If new fasteners are needed, they must be of the same size and grade as the ones that are being replaced.The material strength identification is usually shown on the bolt head by numbers (8.8, 10.9, etc.). The following chart gives standard torques for bolts and nuts with Grade 8.8.
Metric hardware must be replaced with metric hardware. Check parts manual for proper replacement.Metric Nuts and Bolts
Metric Taperlock Studs
Standard Torque for Worm Drive Band Hose Clamps
Typical hose clamp. Standard Torque for Constant Torque Hose Clamps
Use a constant torque hose clamp in place of any standard hose clamp. Ensure that the constant torque hose clamp is the same size as the standard hose clamp. Due to extreme temperatures changes, the hose will heat set. Heat setting can cause hose clamps to loosen. Loose hose clamps can result in leaks. There have been reports of component failures that have been caused by hose clamps that have loosened. The constant torque hose clamp will help prevent these failures. Use a torque wrench for proper installation of the constant torque hose clamps. The constant torque hose clamp is installed correctly under the following conditions:* Screw tip (1) extends 6.35 mm (.250 inch) (X) beyond the housing.* The belleville washers are collapsed nearly flat after screw (2) is tightened to a torque of 11 1 N m (98 9 lb in).Torques for Ground Engaging Tool Bolts
Torques for Track Shoe and Bucket Side Cutter Bolts
Torques for Swivel Nuts on Hydraulic Hoses
The following chart gives general torques for swivel nuts on existing hydraulic hoses.
Torques for Bolts on Major Components
Torques for Undercarriage Bolts


Parts brkt Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.