AVSPARE.COM
parts catalog

BUCKET AS-EXCAVATION 1694931 - Caterpillar



1694931 BUCKET AS-EXCAVATION Caterpillar parts 345B L BUCKET
Rating:
32
Alternative (cross code) number:
CA1694931
169-4931
1694931
Caterpillar 1694931 BUCKET AS-EXCAVATION

Buy BUCKET AS-EXCAVATION 1694931 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 1694931:

EXCAVATOR  345B L   Caterpillar
  For full view, you need register

Information:

Use this procedure to troubleshoot any suspect problems with the Cat Data Link.Use this procedure to troubleshoot the system when one of the following diagnostic codes is active or easily repeated:
296-09 Unable to communicate with Transmission ECM
296-12 Transmission ECM Failed
1639-09 Machine Security System Module not communicating on linkNote: This procedure checks for an open circuit or for a short circuit in the Cat Data Link. If you are experiencing problems with communications between the Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM), refer to the troubleshooting without a diagnostic code procedure Troubleshooting, "Electronic Service Tool Will Not Communicate with ECM" before you use this procedure.The Cat Data Link is the standard Data Link that is used by the ECM to communicate with Cat ET. The ECM communicates with Cat ET in order to share status information and diagnostic information. Cat ET can also be used to configure the ECM parameters. This information will not be available if communication fails between the ECM and Cat ET.
Illustration 1 g01222915
Schematic for the "Cat Data Link"
Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01167488
Engine view (typical example)
(1) J1/P1 connectors
Thoroughly inspect connector (1). Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01104274
P1 terminals that are associated with the "Cat Data Link"
(P1-8) Cat Data Link +
(P1-9) Cat Data Link −
Illustration 4 g01222949
Terminals that are associated with the "Cat Data Link" on the machine connector
(P1-40) Cat Data Link +
(P1-39) Cat Data Link −
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the "Cat Data Link".
Check the allen head screw on each ECM connector for the proper torque. Also, check the allen head screw on the customer connector for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect". Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or the wiring are not OK.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the original problem is resolved.STOPTest Step 2. Check for a Short Circuit
Disconnect the P1 ECM connector.
Disconnect Cat ET from the service tool connector.
Disconnect any other control modules from the "Cat Data Link". Refer to Illustration 1.
Measure the resistance between the points that are listed in Table 1. Be sure to wiggle the wires in the harnesses as you make each resistance measurement.
Table 1
Resistance Measurements for the Cat Data Link
Connector and Terminal Terminal
P1-8 (Cat Data Link +) All of the other terminals on the P1 connector
Ground stud
P1-9 (Cat Data Link -) All of the other terminals on the P1 connector
Ground stud Expected Result:Each check of

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts bucket Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.