AVSPARE.COM
parts catalog

BULB-24V 1C3865 - Caterpillar



1C3865 BULB-24V Caterpillar parts PR-450 BULB
Rating:
32
Alternative (cross code) number:
CA1C3865
1C-3865
1C3865
Caterpillar 1C3865 BULB-24V
Weight: 0.02 pounds 0 kg.

Buy BULB-24V 1C3865 Caterpillar genuine, new aftermarket tractor parts with delivery
COLD PLANER,

Compatible equipment models: 1C3865:

COLD PLANER  PR-450   Caterpillar
Number on catalog scheme: 29
 
  For full view, you need register

Information:


Illustration 1 g06151189
GPS and the Cat® Grade Control System
(1) GPS Satellites
(2) Machine equipped with the Cat® Grade Control System
(3) GPS Base Station and Data Radio
(4) Repeater radio (optional)The method that is used for machine grade control in construction is the same used by surveyors for stakeout in construction. The method is called Real-Time Kinematic (RTK), GPS. Two GPS receivers are required to produce RTK positions. One GPS receiver is known as the GPS base station. The GPS base station has a fixed position. The other GPS receiver is known as the rover. This receiver is mounted on the machine.The base station communicates to the rover through a wireless data link using a data radio. Illustration 1 shows this setup.Both GNSS receivers make observations (measurements) of the GNSS signals at the same time. The base station broadcasts the observed information together with the location and other information across the data radio link to the rover. The rover then combines the data from the base station together with the machine data to compute an accurate position relative to the base station.Note: Poor placement of the reference station can adversely affect the position accuracy of the rover.A single base station can support an unlimited number of rovers, provided the rovers are within about 20 km (12.4 mi) of the base station. Normally, the range of the data radio link is the more limiting factor. The operator can use radio repeaters to extend the radio coverage.Low accuracy corrected GPS (SBAS)
If low accuracy GNSS positions are adequate for the required site work, the operator can use Satellite-Based Augmentation System (SBAS) error corrections. SBAS corrected systems do not require additional site infrastructure.A Satellite-Based Augmentation System (SBAS) supports wide-area or regional augmentation by using additional satellite-broadcast messages. Such systems are commonly composed of multiple ground stations that take measurements of one or more of the GNSS satellites, the satellite signals, or environmental factors that may impact the signal received by users. These measurements are used to send information messages to one or more satellites for broadcast to the end users to augment and improve accuracy, reliability, and availability of GNSS positional information.The following SBAS networks are currently available:
Table 1
WAAS Wide Area Augmentation System (United States)
EGNOS European Geostationary Navigation Overlay Service (Europe)
MSAS Multi-Functional Satellite Augmentation System (Japan) GNSS receivers use a GNSS receiver configuration file (.cfg) to convert from WGS84 coordinates to the site coordinate system. High accuracy (RTK) GNSS systems use a configuration file generated from the site calibration. If the position of the base station entered for site calibration is not accurate, the site coordinate systems will shift away from the local coordinate system. When this faulty receiver configuration file is used by a GNSS RTK receiver, the shift will not be obvious. The site relative positions points will still be accurate and the accuracy of RTK positioning is unaffected. However, if the same receiver configuration file is used by a GNSS receiver that uses SBAS corrections, the shift will become obvious which will result

Caterpillar parts catalog:

Caterpillar parts catalog
PR-450 COLD PLANER 7DC00204-UP (MACHINE) POWERED BY 3408 ENGINE


Parts bulb Caterpillar catalog:

0813314 BULB
CB-434, CB-434B, CB-534, CB-534B, CB-535B, CB-544, CB-545, PF-300C, PS-300, PS-300B
2U4521 BULB 24 V
D25C, D30C, D350C, D35C, D35HP, D400
2U4672 BULB 24 V
D25C, D30C, D350C, D35C, D35HP, D400
2U4701 BULB 4w 24v
D25C, D30C, D350C, D35C, D35HP, D400, D44B, D550B
0780620 BULB
CB-314, CP-433B, CS-431B, CS-551
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.