AVSPARE.COM
parts catalog

BUSHING 3534911 - Caterpillar



3534911 BUSHING Caterpillar parts BUSHING
Rating:
11
Alternative (cross code) number:
CA3534911
353-4911
3534911
Caterpillar 3534911 BUSHING
Weight: 0.33 pounds 0 kg.

Buy BUSHING 3534911 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 54A
 
  For full view, you need register

Information:

Which Generate This Code:Note: This procedure is only for operator errors originating from the Conveyor Electronic Control System. The operator error codes are viewed on the ECM three digit display. Refer to the procedure that corresponds to the operator error code that is being shown on the ECM display. P01 Error Code - No Automatic OperationThis operator error is recorded when the conveyor ECM determines that the propel ECM is not in a paving condition.The possible causes of this error code are:
The propel lever is not in FORWARD
The propel switch is not in PAVE. For the AP1000B and the BG260C, the propel switch is not in LOW.
The propel speed dial is at the MINIMUM position.
There are active propel ECM diagnostic codes involving the propel lever, the propel switch, the propel speed dial, or the propel Cat Data Link.
The propel ECM or the conveyor ECM is faulty. This is unlikely.System Response:The results of this error code are:
The augers and the conveyors will not run in the AUTO mode.Note: Ensure that "PO1" error code is active and that the conveyor diagnostic code lamp is ON.Test Step 1. Check Operator Settings
Turn the key start switch ON.
Move the propel switch to the PAVE position. (NOT in LOW for the AP1000B and the BG260C.
Move the propel lever to the FORWARD position.
Turn the propel speed dial to a position other than MINIMUM.
Check to see if the P01 error code is still present.Expected Result:The P01 error code is not present.Results:
OK - The P01 operator error is not present. The system is working properly. Stop.
Not OK - The P01 error code is still present. Proceed to Test Step 2.Test Step 2. Check Conveyor ECM For Diagnostic Codes.
Access service mode 1 on the conveyor ECM. Refer to the "Accessing Diagnostic Information" module in this manual.
Check to see if a CID 248 FMI F11 diagnostic code is active.Expected Result:A CID 248 FMI F11 diagnostic code is active.Results:
OK - A CID 248 FMI F11 diagnostic code is active.Repair: Perform the troubleshooting procedure that is listed for the active diagnostic code in the troubleshooting section of this manual. Stop.
NOT OK - A CID 248 FMI F11 diagnostic code is not active. Proceed to Test Step 3.Test Step 3. Check Propel ECM For Service Codes
Access service mode 1 on the propel ECM. Refer to the Service Manual, Propel Electronic Control System, "Accessing Diagnostic Information".
On the propel ECM, check to see if a diagnostic code is active for one of the following components:
Propel lever
Propel switch
Propel speed dial
Cat Data Link Expected Result:A diagnostic code for a component in the preceding list is active.Results:
OK - A diagnostic code for a component in the preceding list is active.Repair: Refer to the Service Manual, Propel Electronic Control System, "Diagnostic Code Procedures". Perform the procedure for the active diagnostic code of the component. Stop.
NOT OK - A diagnostic code for a component in the preceding list is not active.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. Refer to

Caterpillar parts catalog:

Caterpillar parts catalog
CX38-P800 Powertrain Package-Well Service Transmission A3X00001-UP
CX38-P892-C18I Petroleum Power Train Package A3X00001-UP POWERED BY C18 Industrial Engine
745 Articulated Truck 3T600001-UP (MACHINE) POWERED BY C18 Engine
740EJ Articulated Truck 3T700001-UP (MACHINE) POWERED BY C18 Engine
745 Articulated Truck 3F600001-UP (MACHINE) POWERED BY C18 Engine
740 EJ Articulated Truck 3F700001-UP (MACHINE) POWERED BY C18 Engine
740 Articulated Truck 3T800001-UP (MACHINE) POWERED BY C15 Engine
740 Articulated Truck 3F800001-UP (MACHINE) POWERED BY C15 Engine
735C Articulated Truck TFJ00001-UP (MACHINE) POWERED BY C15 Engine
735C Articulated Truck LFJ00001-UP (MACHINE) POWERED BY C15 Engine
745C Articulated Truck TFK00001-UP (MACHINE) POWERED BY C18 Engine
745C Articulated Truck LFK00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck TFN00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck LFN00001-UP (MACHINE) POWERED BY C18 Engine


Parts bushing Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.