AVSPARE.COM
parts catalog

BUSHING 3534912 - Caterpillar



3534912 BUSHING Caterpillar parts BUSHING
Rating:
16
Alternative (cross code) number:
CA3534912
353-4912
3534912
Caterpillar 3534912 BUSHING
Weight: 0.23 pounds 0 kg.

Buy BUSHING 3534912 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 85A
 
  For full view, you need register

Information:

Which Generate This Code:Note: This procedure is only for operator errors originating from the Conveyor Electronic Control System. The operator error codes are viewed on the ECM three digit display. P02 Error Code - System FaultNote: When this error occurs and the paving operation must continue, the P02 error code can be bypassed. Moving the feeder mode switch to the OFF position and then back to the AUTO position will bypass the P02 error. The conveyor ECM will now assume that the propel ECM is in the paving state and the conveyors and augers will be able to operate. The P02 error code is no longer showing on the readout. The diagnostic lamp for the feeder remains ON because a CID 248 diagnostic code is recorded. :When the P02 error code is bypassed, then the auger and the conveyor can operate during any propel range (pave, travel, maneuver) and any propel direction (forward, neutral or reverse). This operator error is recorded when the propel ECM is not communicating with the conveyor ECM and the system is turned ON.The possible causes of this error code are:
There is a diagnostic code for the Cat Data Link on the conveyor ECM.
There is a diagnostic code for the Cat Data Link on the propel ECM.
The conveyor ECM is malfunctioning or the propel ECM is malfunctioning. This is unlikely.System Response:The results of this error are:
The diagnostic code lamp for the feeder will be ON.
The augers and conveyors will not run in AUTO mode.Test Step 1. Check Conveyor ECM For Diagnostic Codes
Access service mode 1 on the conveyor ECM. Refer to the "Accessing Diagnostic Information" section of this manual.
Check to see if a CID 248 FMI F11 diagnostic code is active.Expected Result:A CID 248 FMI F11 diagnostic code is active.Results:
OK - A CID 248 FMI F11 diagnostic code is active.Repair: Perform the troubleshooting procedure that is listed for the active diagnostic code in the "Diagnostic Code Procedures" section of this manual. Stop.
NOT OK - A CID 248 FMI F11 diagnostic code is not active. Proceed to Test Step 2.Test Step 2. Check Propel ECM For Diagnostic Codes
Access service mode 1 on the propel ECM. Refer to the Service Manual, Propel Electronic Control System, "Accessing Diagnostic Information".
On the propel ECM, check to see if a diagnostic code is active for the Cat Data LinkExpected Result:A diagnostic code for the Cat Data Link is active.Results:
OK - A diagnostic code for the Cat Data Link is active.Repair: Refer to the Service Manual, Propel Electronic Control System, "Diagnostic Code Procedures". Perform the procedure for the diagnostic code that is for the Cat Data Link. Stop.
NOT OK - A diagnostic code for the Cat Data Link is not active. Proceed to Test Step 3Test Step 3. Check Cat Data Link for Open
Turn the key switch to the OFF position.
Disconnect the conveyor ECM from the machine harness. Disconnect the propel ECM from the machine harness.
At the machine harness connector for the conveyor ECM, measure the resistance from connector contact

Caterpillar parts catalog:

Caterpillar parts catalog
CX38-P800 Powertrain Package-Well Service Transmission A3X00001-UP
CX38-P892-C18I Petroleum Power Train Package A3X00001-UP POWERED BY C18 Industrial Engine
745 Articulated Truck 3T600001-UP (MACHINE) POWERED BY C18 Engine
740EJ Articulated Truck 3T700001-UP (MACHINE) POWERED BY C18 Engine
745 Articulated Truck 3F600001-UP (MACHINE) POWERED BY C18 Engine
740 EJ Articulated Truck 3F700001-UP (MACHINE) POWERED BY C18 Engine
740 Articulated Truck 3T800001-UP (MACHINE) POWERED BY C15 Engine
740 Articulated Truck 3F800001-UP (MACHINE) POWERED BY C15 Engine
735C Articulated Truck TFJ00001-UP (MACHINE) POWERED BY C15 Engine
735C Articulated Truck LFJ00001-UP (MACHINE) POWERED BY C15 Engine
745C Articulated Truck TFK00001-UP (MACHINE) POWERED BY C18 Engine
745C Articulated Truck LFK00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck TFN00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck LFN00001-UP (MACHINE) POWERED BY C18 Engine


Parts bushing Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.