AVSPARE.COM
parts catalog

BUSHING 3534913 - Caterpillar



3534913 BUSHING Caterpillar parts BUSHING
Rating:
21
Alternative (cross code) number:
CA3534913
353-4913
3534913
Caterpillar 3534913 BUSHING
Weight: 0.13 pounds 0 kg.

Buy BUSHING 3534913 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 85B
 
  For full view, you need register

Information:

Which Generate This Code:Note: This procedure is only for operator errors originating from the Conveyor Electronic Control System. The operator error codes are viewed on the ECM three digit display. P02 Error Code - Sonic Sensors Out Of Range (if equipped)This operator error is recorded when the sonic sensors are too close to the material or the sonic sensors are too far away from the material.The possible causes of this error code are:
The sonic sensor is too close to the material. This occurs when the distance to the material is less than 152 mm (6 inches).
The sonic sensor is too far from the material. This occurs when the distance to the material is greater than 1270 mm (50 inches).
There is a diagnostic code that involves one or both of the sonic sensors. The codes can be a CID 022 or a CID 032.
The conveyor ECM is malfunctioning. This is unlikely.System Response:The results of this error are:
The diagnostic code lamp for the feeder will be ON.
The augers and the conveyors that are on same side as the problem sensor will not run in the AUTO mode.Test Step 1. Check Placement Of Sonic Sensor
Refer to the installation procedure for the sonic sensors.
The sensors should be adjusted so that they are clear of the screed when the screed is raised and lowered.
During machine operation, the sensor should be mounted between 381.0 mm (15.0 inches) and 914.4 mm (36.0 inches) from the material.Expected Result:The sensors are not mounted correctly.Results:
OK - The sensors are not mounted correctly.Repair: Position the sensors within the proper range. Stop.
NOT OK - The sensors are mounted correctly. Proceed to Test Step 2.Test Step 2. Check the ECM For Diagnostic Codes
Access service mode 1 on the ECM. Refer to "Accessing Diagnostic Information" in this Manual.
Check to see if a CID 022 code for the left sonic sensor is active.
Check to see if a CID 032 code for the right sonic sensor is active.Expected Result:One of the diagnostic codes for the left or right sonic sensor is active.Results:
OK - One of the sonic sensor diagnostic codes is active.Repair: Refer to the topic "Diagnostic Code Procedures" in this manual. Perform the procedure for the sonic sensor diagnostic code that is active on the ECM. Stop.
NOT OK - Neither of the sonic sensor diagnostic codes is active. Proceed to Test Step 3.Test Step 3. Check To See If Diagnostic Code Remains
Turn the key start switch to the ON position.
Enter service mode 1 on the ECM three digit display. Clear all inactive diagnostic codes.
Operate the machine.
Check to see if the P03 diagnostic code for the sonic sensor is present.Expected Result:The P03 error code is no longer active.Results:
OK - The P03 error code is no longer active.Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation. Stop.
Not OK - The P03 error code is still active.Repair: The sonic sensor has failed. Replace the

Caterpillar parts catalog:

Caterpillar parts catalog
CX38-P800 Powertrain Package-Well Service Transmission A3X00001-UP
CX38-P892-C18I Petroleum Power Train Package A3X00001-UP POWERED BY C18 Industrial Engine
745 Articulated Truck 3T600001-UP (MACHINE) POWERED BY C18 Engine
740EJ Articulated Truck 3T700001-UP (MACHINE) POWERED BY C18 Engine
745 Articulated Truck 3F600001-UP (MACHINE) POWERED BY C18 Engine
740 EJ Articulated Truck 3F700001-UP (MACHINE) POWERED BY C18 Engine
740 Articulated Truck 3T800001-UP (MACHINE) POWERED BY C15 Engine
740 Articulated Truck 3F800001-UP (MACHINE) POWERED BY C15 Engine
735C Articulated Truck TFJ00001-UP (MACHINE) POWERED BY C15 Engine
735C Articulated Truck LFJ00001-UP (MACHINE) POWERED BY C15 Engine
745C Articulated Truck TFK00001-UP (MACHINE) POWERED BY C18 Engine
745C Articulated Truck LFK00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck TFN00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck LFN00001-UP (MACHINE) POWERED BY C18 Engine


Parts bushing Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.