1245979 CAGE-BEARING Caterpillar parts 30/30, DEUCE CAGE
Rating:
Alternative (cross code) number:
CA1245979
124-5979
1245979
CA1245979
124-5979
1245979
Buy CAGE-BEARING 1245979 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 311-1362 Vacuum Gauge Gp 1
B - Loctite 271 - Start By:
Release the hydraulic system pressure.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g02138430
Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 2 g02138375
Remove bolts (2) and plate assembly (1) .
Illustration 3 g02245313
Disconnect harness assemblies (4) and hose assemblies (6) .
Remove bolts (3) and solenoid valve (tool control) (5) .
Illustration 4 g02245314
Remove bolts (9) and solenoid valve (7) .
Remove pressure sensor (8) and plugs (10) .
Illustration 5 g02245836
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove plug (16), O-ring seal (15), spring (14), seat (13), valve (12), and O-ring seal (11) .Installation Procedure
Install solenoid valve (tool control) (5) in the reverse order of removal.
Tighten plug (16) to a torque of 29 2 N m (21 1 lb ft).
Tighten plugs (10) to a torque of 9 1 N m (80 9 lb in).
Tighten bolts (9) to a torque of 7 1 N m (62 9 lb in).
Tighten pressure sensor (8) to a torque of 48 5 N m (35 4 lb ft).
Apply Tooling (B) to the threads of bolts (2) .
Check the hydraulic oil level. Refer to, "Hydraulic System Oil Level - Check".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 311-1362 Vacuum Gauge Gp 1
B - Loctite 271 - Start By:
Release the hydraulic system pressure.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g02138430
Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 2 g02138375
Remove bolts (2) and plate assembly (1) .
Illustration 3 g02245313
Disconnect harness assemblies (4) and hose assemblies (6) .
Remove bolts (3) and solenoid valve (tool control) (5) .
Illustration 4 g02245314
Remove bolts (9) and solenoid valve (7) .
Remove pressure sensor (8) and plugs (10) .
Illustration 5 g02245836
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove plug (16), O-ring seal (15), spring (14), seat (13), valve (12), and O-ring seal (11) .Installation Procedure
Install solenoid valve (tool control) (5) in the reverse order of removal.
Tighten plug (16) to a torque of 29 2 N m (21 1 lb ft).
Tighten plugs (10) to a torque of 9 1 N m (80 9 lb in).
Tighten bolts (9) to a torque of 7 1 N m (62 9 lb in).
Tighten pressure sensor (8) to a torque of 48 5 N m (35 4 lb ft).
Apply Tooling (B) to the threads of bolts (2) .
Check the hydraulic oil level. Refer to, "Hydraulic System Oil Level - Check".
Caterpillar parts catalog:
Parts cage Caterpillar catalog:
1245982
CAGE-BEARING
30/30, DEUCE
30/30, DEUCE
8P8700
CAGE-BEARING
30/30, 611, 615, 615C, AD30, D250D, D250E, D250E II, D25C, D25D, D300B, D300D, D300E, D300E II, DEUCE, R1600, R1600G, R1600H
30/30, 611, 615, 615C, AD30, D250D, D250E, D250E II, D25C, D25D, D300B, D300D, D300E, D300E II, DEUCE, R1600, R1600G, R1600H
1422051
CAGE-BEARING
30/30, DEUCE
30/30, DEUCE
2018030
CAGE AS
30/30, DEUCE
30/30, DEUCE
1245989
CAGE AS
30/30, DEUCE
30/30, DEUCE
1245981
CAGE-BEARING
30/30, DEUCE
30/30, DEUCE
1245990
CAGE AS
30/30, DEUCE
30/30, DEUCE
1245980
CAGE-BEARING
30/30, DEUCE
30/30, DEUCE
1268176
CAGE AS
30/30, DEUCE
30/30, DEUCE
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, DEUCE,...
1268176
CAGE AS
30/30, DEUCE
30/30, DEUCE
1245980
CAGE-BEARING
30/30, DEUCE
30/30, DEUCE
1245990
CAGE AS
30/30, DEUCE
30/30, DEUCE
1245981
CAGE-BEARING
30/30, DEUCE
30/30, DEUCE
1245989
CAGE AS
30/30, DEUCE
30/30, DEUCE
2018030
CAGE AS
30/30, DEUCE
30/30, DEUCE
3576623
CAGE AS-BEARING
SPF343C, TH48-E80
SPF343C, TH48-E80
2935858
CAGE AS-BEARING
SPF343C, TH48-E80
SPF343C, TH48-E80
2750690
CAGE AS-BEARING
SPF343C, TH48-E80
SPF343C, TH48-E80
2709582
CAGE AS-BEARING
TH48-E80
TH48-E80
3626038
CAGE AS-BEARING
TH48-E80
TH48-E80
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, DEUCE,...