AVSPARE.COM
parts catalog

CASE AS-DIFFERENTIAL 9V9486 - Caterpillar



9V9486 CASE AS-DIFFERENTIAL Caterpillar parts 834B, 988B CASE
Rating:
11
Alternative (cross code) number:
CA9V9486
9V-9486
9V9486
Caterpillar 9V9486 CASE AS-DIFFERENTIAL
Weight: 198 pounds 89 kg.

Buy CASE AS-DIFFERENTIAL 9V9486 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL DOZER, WHEEL LOADER,

Compatible equipment models: 9V9486:

WHEEL DOZER  834B  
WHEEL LOADER  988B   Caterpillar
Number on catalog scheme: 3
 
  For full view, you need register

Information:

The angle of the installation and the slant of the installation will affect the engine oil level. The angle is the front to back tilt of the engine. The slant is the sideways tilt of the engine.
Illustration 1 g00403460
The engine will be equipped with either dipstick.
(1) Traditional dipstick. (2) Full range dipstick.
Verify that the markings on the engine oil level gauge are correct. Verify the markings at the first oil change.Use the following procedure in order to verify that "ADD" mark is correct. Use the following procedure in order to establish actual "FULL" mark on the engine oil level gauge.
The engine must be on a level surface to perform this maintenance procedure.
Operate the engine until normal operating temperature is achieved. Stop the engine. Remove the drain plugs from the engine crankcase. Allow the engine oil to drain.
Do not fill the oil filters with oil before installing them.This oil would not be filtered and could be contaminated.Contaminated oil will cause accelerated wear to the engine.
Remove the used engine oil filter(s). Install the new engine oil filter(s). Install the drain plug for the engine crankcase. Tighten the drain plug for the engine crankcase to 70 14 N m (50 10 lb ft). Note: The engine may be equipped with auxiliary engine oil filters. The oil filters may require a different volume than the standard amount. Refer to the OEM specifications.
Pour 26.5 L (28 qt) of engine oil into the engine crankcase. DO NOT pour oil into the oil filler that is located on top of the engine. Pour oil into one of the oil fill locations on the side of the engine. Allow enough time for the engine oil to drain into the engine crankcase. Check the engine oil level. Wait for a few minutes. Check the engine oil level again. Proceed after the engine oil level stops changing.
The oil level should be at the "ADD" mark. If the oil is not at the "ADD" mark, grind off the existing "ADD" mark. Mark the new level as "ADD" using an engraving pen.
Pour 5.7 L (6 qt) of engine oil into the engine crankcase. Allow enough time for the engine oil to drain into the engine crankcase. Allow a minimum of five minutes.
Install the oil level gauge. Remove the gauge and note the oil level on the gauge. This is the new "FULL" mark on the dipstick. If the oil is not at the "FULL" mark, grind off the existing "FULL" mark. Mark the new level as "FULL" using an engraving pen.
Pour 5.7 L (6 qt) of engine oil into the engine crankcase for the filter or filters and margin.
Start the engine. Ensure that the lubrication system is filled. Inspect the lubrication system for leaks.
Stop the engine and allow enough time for the engine oil to drain into the engine crankcase. Allow a minimum of five minutes.
Check the engine oil level on the engine oil level gauge. If the engine oil level is not at the calibrated "FULL" mark, fill

Caterpillar parts catalog:

Caterpillar parts catalog
988B Wheel Loader 50W06041-UP (MACHINE) POWERED BY 3408 Engine


Parts case Caterpillar catalog:

8P3155 CASE-TRANSMISSION
826C, 834B, 836, 980C, 980F, 988B, D350E, D350E II, D400E
6W8261 CASE AS-DIFFERENTIAL
990, 990 II, 992C, 992D
2V3954 CASE AS
824C, 980C, 980F, D44B, D550B
3T7389 CASE AS-TRANSFER
824C, 826C, 834B, 980C, 988B, D44B, D550B
3T6171 CASE-TRANSFER
834B, 836, 988B, D350E, D350E II, D35HP, D400, D400E, D40D, D550B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.