parts catalog

CLAMP 0003858 - Caterpillar

0003858 CLAMP Caterpillar parts WE-601B CLAMP
Alternative (cross code) number:
Caterpillar 0003858 CLAMP

Buy CLAMP 0003858 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 0003858:

WINDROW ELEVATOR  WE-601B   Caterpillar
Number on catalog scheme: 9
  For full view, you need register


Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from the sudden release of high pressure oil.Be sure the engine has been shut off for a minimum of five minutes to be sure that the accumulator pressure is zero.The accumulator is filled with dry nitrogen. Do not loosen or remove the valve or cap from the top of the accumulator. A purge screw at the bottom of the accumulator can be used to release the pressure that is left in the system.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification on all lines and on all hoses for installation purposes. Plug all lines and all hoses. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure - Release".
Illustration 1 g01397769
Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 138 kPa (20 psi). This procedure will pull a vacuum on the hydraulic system.
Engage the parking brake.
Illustration 2 g01404183
The engine enclosure was removed for photographic purposes.
Disconnect fitting (3). Remove bolts (1). Remove clamps (2).
Remove brake accumulator (4).
Repeat Step 4 through Step 5 for the remaining brake accumulator. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 311-1362 Vacuum Cap 1
Personal injury or death can result from improper accumulator charging.Dry nitrogen is the only gas approved for use in the accumulator. Charging the accumulator with oxygen gas will cause an explosion. This danger will not happen if nitrogen cylinders with standard CGA Compressed Gas Association, Inc.Number 580 connections are used.When ordering nitrogen gas, be sure that the cylinders are equipped with CGA Number 580 Connections. Do not use color codes or other methods of identification to tell the difference between nitrogen and oxygen cylinders.Never use an adapter to connect your nitrogen charging group to a valve outlet used on both nitrogen, oxygen or other gas cylinders. Be sure you use dry nitrogen (99.8

Caterpillar parts catalog:

Caterpillar parts catalog

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.