AVSPARE.COM
parts catalog

COMMON AR 4645036 - Caterpillar



4645036 COMMON AR Caterpillar parts COMMON
Rating:
81
Alternative (cross code) number:
CA4645036
464-5036
4645036
Caterpillar 4645036 COMMON AR

Buy COMMON AR 4645036 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01322198
Schematic for the Winch Free Spool SwitchThe Winch Free Spool Switch has two inputs to the ECM. The two inputs are normally open and normally closed. During normal operation, one of the inputs is open. The other input is grounded. When a circuit is measured with a voltmeter, an open circuit will measure approximately 13 DCV to ground and a closed circuit will measure approximately 0 DCV to ground. An FMI 04 diagnostic code is recorded when both of the inputs are grounded.The possible causes of this diagnostic code are listed below:
The "normally open" signal circuit (wire P784-OR) is always shorted to ground.
The "normally closed" signal circuit (wire P783-WH) is always shorted to ground.
The switch has failed.
The ECM has failed. This is unlikely. Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.
Table 1
Status of the Switch    
MODE    Switch Position    J2-37 (N/O)
P784-OR Circuit    J2-36 (N/C)
P783-WH Circuit    
Released     Up     Open     Closed    
Pressed     Down     Closed     Open    System Response:A level 1 warning is generated.Test Step 1. CHECK THE SWITCH
Check for continuity between contact 1 and contact 2 of the switch.
Press the switch and then release the switch while checking for continuity.
Check for continuity between contact 2 and contact 3 of the switch.
Press the switch and then release the switch while checking for continuity.Expected Result:The continuity check agrees with the preceding Table.Results:
OK - The continuity check agrees with the preceding Table. Proceed to Test Step 2.
NOT OK - The continuity check does not agree with the preceding Table. The switch has failed.Repair: Replace the switch. Verify that the new switch corrects the diagnostic code.STOPTest Step 2. CHECK THE SIGNAL CIRCUITS FOR A SHORT TO GROUND
Reconnect the switch to the machine harness.
The machine harness connectors remain disconnected from the ECM.
At the machine harness connector for the ECM, check for continuity between contact J2-37 (wire P784-OR) and frame ground.
Press the switch and then release the switch while checking for continuity.
At the machine harness connector for the ECM, check for continuity between contact J2-36 (wire P783-WH) and frame ground.
Press the switch and then release the switch while checking for continuity.Expected Result:The continuity check agrees with the preceding Table.Results:
OK - The continuity check agrees with the preceding Table.Repair: If the cause of the problem is not found, contact the Technical Communicator for your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, see Troubleshooting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - The continuity check does not agree with the preceding Table.Repair: There is a short in the machine harness. Repair the machine harness or replace the machine harness.STOP

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
725C2 Articulated Truck 2T300001-UP (MACHINE) POWERED BY C9.3 Engine


Parts common Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.