AVSPARE.COM
parts catalog

CONTROL GP-PRESSURE 9V9315 - Caterpillar



9V9315 CONTROL GP-PRESSURE Caterpillar parts 215, 215B CONTROL
Rating:
56
Alternative (cross code) number:
CA9V9315
9V-9315
9V9315
Caterpillar 9V9315 CONTROL GP-PRESSURE
Weight: 0.95 pounds 0 kg.

Buy CONTROL GP-PRESSURE 9V9315 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 9V9315:

EXCAVATOR  215   215B   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Removal Procedure
If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Open the hood and remove the left side engine panel.
Illustration 1 g03358364
Loosen clamp assemblies (1), (3), and (4). Note: Mark the orientation of clamp assembly (3) prior to removal.
Slide elbow (5) into bellows (4) in order to gain clearance. Remove the bellows assembly. Installation Procedure
If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Illustration 2 g02486200
Illustration 3 g02486204
Alignment Wrap (A) is not shown for photographic purposes. Typical Example
Note: Alignment Wrap (A) will be included with the new bellows assembly. The Tooling will be pre-installed on the bellows.Note: The alignment Wrap (A) should not be removed until Step 11. Bellows (2) should never be flexed during installation.
Distance (X) is 40 mm (1.6 inch). Place Mark (B) onto elbow (5). a Distance (X) from the end of elbow (5).
Insert elbow (5) into the bellows. The elbow should be inserted as far as possible without using force. This action will minimize the overall length of the bellows assembly and will help with installation.
Illustration 4 g03358364
Prior to installation, position both ball clamp assemblies (1) and (4).
Position the bellows assembly between the Clean Emissions Module and the turbocharger adapter. Adjust the length of elbow (5) in the slip joint at clamp assembly (3) in order to position the bellows assembly.
Illustration 5 g02486244
The photo is a cutaway view of the ball clamp assembly.
Illustration 6 g02486279
Verify that the cup of the Ball Joint (E) does not touch the radius of the Ball (D). Position ball clamp (1) and hand tighten ball clamp (1). Measure Distance (Y) and Distance (Z). The two measurements should be equal. Repeat the measurements every 90° around ball clamp (1). If necessary, adjust ball clamp (1).
Repeat Step 6 for ball clamp (4) which is located near the turbocharger.
Verify that Mark (B) is not visible at the slip joint that is positioned near clamp assembly (3). Note: Do not use power tools in order to torque clamp assemblies (1), (3), and (4).
Torque ball clamp (1) to a torque of 35 2 N m (26 1 lb ft).
Torque ball clamp (4) to a torque of 35 2 N m (26 1 lb ft).
Remove alignment Wrap (A) from bellows (4).
Torque clamp assembly (3) to a torque of 55 8 N m (41 6 lb ft).
Install the left side engine panel and close the hood.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
215 EXCAVATOR 95Z00001-UP (MACHINE) POWERED BY 3304 ENGINE
215B EXCAVATOR 9YB00001-UP (MACHINE) POWERED BY 3304 ENGINE


Parts control Caterpillar catalog:

6C0338 CONTROL GP-GOVERNOR
215, 215B, 215C, 215D, 219D
5C6626 CONTROL GP-PILOT OPERATED HYD
215, 215B, 215C, 215D, 219D, 225, 225D, 229, 235, 235B, 235C
3V4487 CONTROL GP-SWING BRAKE
215, 215B, 215C, 215D, 219D, 225, 225D, 227, 229, 229D, 231D
3K8108 CONTROL ASSEM.
215, 225, 769, 772, 824B, 950, 966C, 988
2853590 CONTROL GP-HANDLE
CB-434D, CB-534D, CB-564D, CB-634D
2656695 CONTROL GP-FOOT BRAKE
950H, 962H, 966H, 972H, IT62H
8I0338 CONTROL GP-THICKNESS
10 FT, 10-20B, 8 FT, 8-16B, AP-800C, BG-225B, BG-245C
2851789 CONTROL AR-AUXILIARY
345D, 345D L, 345D L VG, 349D, 349D L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.