AVSPARE.COM
parts catalog

CONVERSION AR-MACHINE 3156354 - Caterpillar



3156354 CONVERSION AR-MACHINE Caterpillar parts 256C, 262C, 262C2, 272C CONVERSION
Rating:
27
Alternative (cross code) number:
CA3156354
315-6354
3156354
Caterpillar 3156354 CONVERSION AR-MACHINE

Buy CONVERSION AR-MACHINE 3156354 Caterpillar genuine, new aftermarket tractor parts with delivery
SKID STEER LOADER,

Compatible equipment models: 3156354:

SKID STEER LOADER  256C   262C   262C2   272C   Caterpillar
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4077 Camshaft Bearing Tool Group 1
125-2739 (1) Bearing Pilot 1
125-2740 (1) Back Up Plate 1
125-2741 (1) Bearing Sleeve 1
B 8S-2241 Camshaft Bearing Tool Group 1
C 316-1493 Hydraulic Puller As 1
D 8H-0684 Ratchet Wrench 1
(1) Alternate Tooling for camshaft bearings with a large diameterStart By:
Remove the camshafts. Refer to Disassembly and Assembly, "Camshaft - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00578295
Typical example
Illustration 2 g00578306
Typical example
Use the following steps to install Tooling (A).
Install the pilot group in the camshaft bearing.
Place the backup plate in position and ensure that the bearing is between the two parts.
Install the bolt that holds Tooling (A) together.
Use the extensions to obtain the correct length for Tooling (A).
Install the puller plate on the bolt and the flywheel housing or the front housing.Note: Tooling (B) can be used to remove the camshaft bearings when the flywheel housing and the front housing have been removed.
Install Tooling (C) on Tooling (A) and pull the bearing from the cylinder block.Note: Tooling (D) can be used in place of Tooling (C), if necessary.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts conversion Caterpillar catalog:

6Y2176 CONVERSION AR-WINCH
931B, 931C, 931C II, 935B, 935C, 935C II, D3B, D3C, D3C II, D4B, D4C, D4C II, D5C
2583812 CONVERSION AR-ROADING
277C, 277C2, 279C, 287C, 287C2, 289C, 297C, 299C
1586170 CONVERSION AR-GENERATOR SET
3508, 3508B, 3512, 3512B, 3516, 3516B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.