AVSPARE.COM
parts catalog

CORE AS-OIL COOLER 1246026 - Caterpillar



1246026 CORE AS-OIL COOLER Caterpillar parts 793C CORE
Rating:
15
Alternative (cross code) number:
CA1246026
124-6026
1246026
Caterpillar 1246026 CORE AS-OIL COOLER

Buy CORE AS-OIL COOLER 1246026 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK,

Compatible equipment models: 1246026:

TRUCK  793C   Caterpillar
  For full view, you need register

Information:


Adjust the speed on the calibration bench to the "LOAD STOP ADJ" rpm that is specified in the TMI. Adjust load stop adjustment screw (4) to the output dimension that is specified in the TMI.
Tighten the locknut for load stop adjustment screw (4) and check the output dimension again.
Increase the speed on the calibration bench by at least 100 rpm. Reduce the speed on the calibration bench back to the "LOAD STOP ADJ" rpm that is specified in the TMI. Check the output dimension again.
If the dimension is not within the "RECHECK TOL" that is specified in the TMI, repeat Step 9.
Adjust the speed on the calibration bench to the "FUNC CHECK #1" rpm that is specified in the TMI. The output dimension must be a maximum of 0.0 mm (0.00 inch).If the output dimension is more than 0.0 mm (0.00 inch), the bearing block assembly must be repositioned. Move the bearing block assembly toward the riser shaft approximately 0.5 mm (0.02 inch). Refer to the Disassembly and Assembly, "Governor (Type) - Disassemble" and Disassembly and Assembly, "Governor (Type) - Assemble" procedures in this manual. Return to Step 9 after installation.
Illustration 4 g00660348
(2) Throttle stop adjustment screw (3) Low idle adjustment screw
Adjust the speed on the calibration bench to the "THROT STOP ADJ" rpm that is specified in the TMI. Adjust throttle stop adjustment screw (2) in order to obtain the output dimension for the "THROT STOP ADJ". Tighten the locknut for throttle stop adjustment screw (2) and check the output dimension again.If the output dimension for the "THROT STOP ADJ" cannot be obtained due to a low output dimension, it will be necessary to move the bearing block assembly away from the riser shaft approximately 0.5 mm (0.02 inch). This will increase the adjustments that are capable for the output dimension. Refer to the Disassembly and Assembly, "Governor (Type) - Disassemble" and Disassembly and Assembly, "Governor (Type) - Assemble" procedures in this manual. Return to Step 9 after installation of the bearing block assembly.Note: After adjustment, at least 2.0 mm (0.08 inch) of the throttle stop screw should extend past the housing surface. This will enable the high idle to be set with the governor on the engine.
Increase the speed on the calibration bench by a minimum of 100 rpm. Then reduce the speed back to the original "THROT STOP ADJ" rpm. Check the output dimension for the "THROT STOP ADJ".If the output dimension is not within the specification that is specified in the TMI, repeat Step 14.
Adjust the speed on the calibration bench to the "FUNC CHECK #2" rpm that is specified in the TMI. The output dimension must be within specifications. If the output dimension is not within specifications, repeat Steps 10 through 15.
Adjust the speed on the calibration bench to the "FUNC CHECK #3" rpm that is specified in the TMI. The output dimension must be within specifications. If the output dimension is not within specifications, inspect the torque cam for wear or damage. Make

Caterpillar parts catalog:

Caterpillar parts catalog
793C Off-HighwayTruck 4AR00001-UP (MACHINE) POWERED BY 3516 Engine
793C Off-Highway Truck 4GZ00001-UP (MACHINE) POWERED BY 3516B Engine


Parts core Caterpillar catalog:

1008008 CORE GP-ENGINE OIL COOLER
5230, 5230B, 785C, 789, 789B, 789C, 793, 793B, 793C, 793D, 994, 994D, 994F
1753185 CORE-VALVE
120H NA, 12G, 12H ES, 12H NA, 130G, 135H NA, 140G, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 24H, 578, 589, 611, 615C, 621E, 621F, 621G, 623E, 623F, 623G, 627E...
2W0181 CORE AS-RADIATOR
3508, 3508B, 3512, 3512B, 3516, 3516B, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 793C, G3512, G3516
2W5540 CORE AS-RADIATOR
16G, 16H, 16H NA, 3406B, 3408, 3412, 572G, 578, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 793C, 814B, 815B, 816B, 966D, D6H, D6H II, D7G, D7H, D8N, G3406
1807180 CORE-VALVE
120M, 12M, 16M, 24M, 5130B, 5230B, 583T, 587T, 613G, 621G, 623G, 627G, 631G, 637G, 651E, 657E, 657G, 725C, 770, 772, 773F, 775F, 777F, 784C, 785C, 789C, 793C, 793D, 797B, 854K, 924K, 930K, 938K, 953D,...
6F3930 CORE-VALVE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
2170311 CORE AS-OIL COOLER
613C, 613C II, 615C, 793C, 815B
2395305 CORE-VALVE
725, 725C, 730, 730C, 735, 735B, 740, 740B, 769D, 770, 770G, 770G OEM, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775E, 775F, 775G, 775G LRC, 775G OEM, 776C, 776D, 777D, 77...
2U0975 CORE
D250B, D250D, D250E, D25C, D25D, D300B, D300D, D300E, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D
2G1951 CORE
768C, 772B, 773B, 777
1506296 CORE AS-RADIATOR
773B, 773D, 773E, 775B, 775D, 775E
2280831 CORE AS-AFTERCOOLER
773B, 773D, 773E, 775B
1367314 CORE AS
D250E II, D300E II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.