AVSPARE.COM
parts catalog

CORE AS 2278368 - Caterpillar



2278368 CORE AS Caterpillar parts CORE
Rating:
16
Alternative (cross code) number:
CA2278368
227-8368
2278368
Caterpillar 2278368 CORE AS
Weight: 26 pounds 11 kg.

Buy CORE AS 2278368 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
LuftMeister 22945153 20980704 22783682 One PCS Front Shock Absorber Without Electric for 2010-2016 Cadillac SRX
$280.00

28 Jul 2022

CN: LuftMeister
LuftMeister 22945153 20980704 22783682 One PCS Front Shock Absorber Without Electric for 2010-2016 Cadillac SRX
LUFT MEISTER Easy to install, but still recommended to be operated by professionals || Adapted model: 2010-2016 Cadillac SRX || OEM Number: 22945153 20980704 22783682
LuftMeister 22945153 20980704 22783682 One PCS Front Shock Absorber Without Electric for 2010-2016 Cadillac SRX
$180.00
 

15 May 2021

CN: LuftMeister
LuftMeister 22945153 20980704 22783682 One PCS Front Shock Absorber Without Electric for 2010-2016 Cadillac SRX
LuftMeister Easy to install, but still recommended to be operated by professionals || Adapted model: 2010-2016 Cadillac SRX || OEM Number: 22945153 20980704 22783682
LuftMeister 22945153 20980704 22783682 One PCS Front Shock Absorber Without Electric for 2010-2016 Cadillac SRX
$180.00
 

15 May 2021

CN: LuftMeister
LuftMeister 22945153 20980704 22783682 One PCS Front Shock Absorber Without Electric for 2010-2016 Cadillac SRX
LuftMeister Easy to install, but still recommended to be operated by professionals || Adapted model: 2010-2016 Cadillac SRX || OEM Number: 22945153 20980704 22783682
  For full view, you need register

Information:

Rear Frame Group
Pivot shaft (10) is not present in all MTS Undercarriage Arrangements. (1) Torque for 20 bolts (four bolts each-five places) ... 430 60 N m (320 44 lb ft)(2) Apply 7M7456 Bearing Mount to frame assembly bore before seal installation.(3) Torque for switch assembly ... 65 5 N m (48 4 lb ft)(4) Apply 5N5561 Silicone Lubricant to seal at assembly.(5) Install nuts (inside and outside) in sequence shown and torque to ... 70 15 N m (50 11 lb ft) Then re-torque in the same sequence to ... 700 70 N m (520 50 lb ft)(6) Apply 5P3931 Anti-Seize Compound to this surface. (7) Bearing bore diameter after assembly ... 140.114 0.160 mm 5.5163 .0063 in)Diameter of pivot shaft in bearing area ... 139.675 0.025 mm (5.4990 .0010 in)(8) Bearing bore diameter after assembly ... 88.774 0.123 mm 3.4950 .0048 in)Diameter of pivot shaft in bearing area ... 88.437 0.025 mm (3.4818 .0010 in)(9) Apply 7M7260 Liquid Gasket to both surfaces at assembly.Front Frame Group
(1) Install bolts in sequence shown and torque to ... 70 15 N m (50 11 lb ft)Then retorque in the same sequence to ... 700 90 N m (520 65 lb ft)(2) Install bolts in sequence shown and tighten finger tight, then torque to ... 28 7 N m (20 5 lb ft)(5) Install wheel assembly with tread pattern as shown.(6) Rubber toric seals and all surfaces in contact with them must be clean and dry at assembly. Put a thin layer of oil on the surfaces of the metal seals that are in contact just before installation. Seal must be assembled square with the bore and toric must not be bulged or twisted.(C) Dimension to press shaft (3) into idler support (4) ... 122.65 0.25 mm (8.333 .010 in)(D) Diameter of shaft ... 89.959 0.015 mm (3.5417 .0006 in)Diameter of idler support ... 89.894 0.015 mm (3.5391 .0006 in)Bearing Adjustment Procedure
This adjustment is to be performed with the belt removed.1. Make sure outboard bearing cone (8) is loose (slides easily) on shaft (3). Make sure locknut (9) rotates easily on the shaft threads. 2. Torque locknut (9) to ... 68 7 N m (50 5 lb ft). 3. Rotate or oscillate hub (7) an equivalent of two full revolutions.4. Repeat Step 2 and Step 3 three additional times.5. If a tang of the lockwasher is not lined up with a slot in locknut (9) at this time, tighten locknut (9) until the most nearly aligned tang and slot line up.Recoil Group
Right Side(1) Use feeler gauge to set gap at ... 1.50 0.25 mm (.060 .010 in)(2) Torque for valve assemblies ... 50 10 N m (37 7 lb ft)(3) Torque for body assembly ... 15 2 N m (11 1 lb ft) Apply


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.