AVSPARE.COM
parts catalog

COVER 7B0183 - Caterpillar



7B0183 COVER Caterpillar parts 44 COVER
Rating:
25
Alternative (cross code) number:
CA7B0183
7B-0183
7B0183
Caterpillar 7B0183 COVER
Weight: 2 pounds 1 kg.

Buy COVER 7B0183 Caterpillar genuine, new aftermarket tractor parts with delivery
HYDRAULIC CONTROL,

Compatible equipment models: 7B0183:

HYDRAULIC CONTROL  44   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:


Table 1
Required Tools
Part Number Part Name Qty
8T-5096 Dial Indicator Gp 1 Face Runout (Axial Eccentricity) of the Flywheel Housing
Illustration 1 g02510176
8T-5096 Dial Indicator Gp
If you use any other method except the method that is given here, always remember that the bearing clearance must be removed in order to receive the correct measurements.
Fasten a dial indicator to the flywheel so the anvil of the dial indicator will contact the face of the flywheel housing.
Use a rubber mallet and tap the crankshaft toward the rear before the dial indicator is read at each point.
Illustration 2 g00285932
Checking face runout of the flywheel housing
Turn the flywheel while the dial indicator is set at 0.0 mm (0.00 inch) at location (A). Read the dial indicator at locations (B), (C), and (D).
The difference between the lower measurements and the higher measurements that are performed at all four points must not be more than 0.38 mm (0.015 inch), which is the maximum permissible face runout (axial eccentricity) of the flywheel housing.Bore Runout (Radial Eccentricity) of the Flywheel Housing
Illustration 3 g02170195
8T-5096 Dial Indicator Gp
Fasten a dial indicator to the flywheel so the anvil of the dial indicator will contact the bore of the flywheel housing.
Illustration 4 g00285932
Checking bore runout of the flywheel housing
Illustration 5 g00763974
While the dial indicator is in the position at location (C), adjust the dial indicator to 0.0 mm (0.00 inch). Push the crankshaft upward against the top of the bearing. Refer to Illustration 5. Write the measurement for bearing clearance on line 1 in column (C).Note: Write the measurements for the dial indicator with the correct notations. This notation is necessary for making the calculations in the chart correctly.
Divide the measurement from Step 2 by two. Write this number on line 1 in columns (B) and (D).
Turn the flywheel in order to put the dial indicator at position (A). Adjust the dial indicator to 0.0 mm (0.00 inch).
Turn the flywheel counterclockwise in order to put the dial indicator at position (B). Write the measurements in the chart.
Turn the flywheel counterclockwise in order to put the dial indicator at position (C). Write the measurement in the chart.
Turn the flywheel counterclockwise in order to put the dial indicator at position (D). Write the measurement in the chart.
Subtract the smaller number from the larger number in column B and column D. Place this number on line III. The result is the horizontal eccentricity (out of round). Line III in column C is the vertical eccentricity.
Illustration 6 g00286046
Graph for total eccentricity
(1) Total vertical eccentricity
(2) Total horizontal eccentricity
(3) Acceptable value
(4) Unacceptable value
Find the intersection of the eccentricity lines (vertical and horizontal) in Illustration 6.
If the point of the intersection is in the “Acceptable” range, the bore is in alignment. If the point of intersection is in the “Not acceptable” range, the flywheel housing must be changed.

Caterpillar parts catalog:

Caterpillar parts catalog
NO. 44 HYDRAULIC CONTROL 06W05001-UP
NO. 44 HYDRAULIC CONTROL 09W00001-UP
NO. 44 HYDRAULIC CONTROL 06W05001-UP
NO. 44 HYDRAULIC CONTROL 09W00001-UP
NO. 44 HYDRAULIC CONTROL 06W05001-UP
NO. 44 HYDRAULIC CONTROL 09W00001-UP


Parts cover Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.