AVSPARE.COM
parts catalog

CUP-BEARING 1C3962 - Caterpillar



1C3962 CUP-BEARING Caterpillar parts PR-750B CUP
Rating:
10
Alternative (cross code) number:
CA1C3962
1C-3962
1C3962
Caterpillar 1C3962 CUP-BEARING
Weight: 6 pounds 2 kg.

Buy CUP-BEARING 1C3962 Caterpillar genuine, new aftermarket tractor parts with delivery
COLD PLANER,

Compatible equipment models: 1C3962:

COLD PLANER  PR-750B   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:

System Operation Description:Use this procedure to troubleshoot any suspect problems with the +5 V sensor supply.Use this procedure to troubleshoot the system when one of the following diagnostic codes is active or easily repeated:
262-03 5 Volt Sensor DC Power Supply short to +batt
262-04 5 Volt Sensor DC Power Supply short to groundThe Electronic Control Module (ECM) supplies a regulated voltage of 5.0 0.2 VDC to the following sensors:
Atmospheric pressure sensor
Boost pressure sensor
Engine oil pressure sensor
Fuel pressure sensor
Auxiliary pressure sensorThe supply for the +5 V engine pressure sensor is routed from the ECM to terminal A of each pressure sensor connector. The sensor return from the ECM connector goes to terminal B of each sensor connector. The 5 V sensor supply is output short circuit protected. A short circuit to the battery will not damage the circuit inside the ECM.Note: The sensors are not protected from overvoltage. A short from the supply line to the +Battery may damage the sensors. If the CID-FMI 262-03 is logged, it is possible that all of the sensors have been damaged. Repair the 5 V sensor supply and check for any active diagnostic codes for the sensor in order to determine if a sensor has failed.A +5 V diagnostic code is probably caused by a short circuit to ground or a short circuit to another voltage source in the harness. The next likely cause is a problem with a sensor. The least likely cause is a problem with the ECM.
Illustration 1 g01212793
Schematic for the 5 volt pressure sensor supplyTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove electrical power from the ECM.
Illustration 2 g01166192
Right side engine view and left side engine view (1) J2/P2 ECM connector (2) J1/P1 ECM connector (3) Fuel pressure sensor (4) Engine oil pressure sensor (5) Atmospheric pressure sensor (6) Boost pressure sensor (7) J61 customer connector
Thoroughly inspect connectors (1) , (2) , and (7) . Also, thoroughly inspect the connectors for each pressure sensor. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01204484
P2 terminal locations (P2-15) Boost pressure (P2-17) Sensor return (P2-28) Engine oil pressure (P2-40) Fuel pressure (P2-57) Atmospheric pressure (P2-72) +5 V supply
Illustration 4 g01212799
P1 ECM connector (P1-2) +5 V supply (P1-3) Sensor return (P1-15) Auxiliary pressure
Illustration 5 g01212800
Terminal locations at the P61 customer connector (Terminal 14) +5 V supply (Terminal 15) Sensor return (Terminal 33) Auxiliary pressure
Illustration 6 g01159881
Sensor connector (Terminal A) +5 V supply (Terminal B) Sensor return (Terminal C) Sensor signal
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors that are associated with the circuit.
Check the allen head screw of each ECM connector and the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasion and for pinch points from the pressure sensors back to the ECM.Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The harness

Caterpillar parts catalog:

Caterpillar parts catalog
PR-750B PAVEMENT PROFILER 8AC00001-UP (MACHINE) POWERED BY 3412 ENGINE
PR-450 COLD PLANER 7DC00204-UP (MACHINE) POWERED BY 3408 ENGINE
PR-1000 PAVEMENT PROFILER 5XC00001-00137 (MACHINE) POWERED BY 3208,3412 ENGINE


Parts cup Caterpillar catalog:

3T3423 CUP
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673C, 16H NA, 16M, 215, 225, 2290, 235...
7K8876 CUP-ROLLER BEARING
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 215, 225, 227, 229, 229D, 231D, 235D, 245, 245B, 245D, 24H, 24M, 35, 45, 518, 5230, 5230B, 528, 54, 55, 623B, 623E, 633D, 789B, 789C, 789D, 793, 793B, 793...
1M8736 CUP-BEARING
205B, 211B, 215, 225, 35, 416, 426, 436, 45, 55, 561M, 561N, 931B, 933, 933C, 939, 939C, 941, 943, 955C, 988B, AP-1050, AP-1055D, AP-650B, AP-655D, BG-225C, BG-245C, BG655D, D3, D3B, D3C III, D3G, D3K...
2P1373 CUP-ROLLER BEARING
215, 215B, 215C, 225, 225D, 227, 229, 229D, 235, 235B, 235C, 235D, 2470C, 2570C, 2670C, 2864C, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 553C, 555D, 563C, 573C, 586C, 589, 65C, 65...
6L3317 CUP ASSEM.
1693, 3406, 3406B, 3408, 3412, D348, D379B, PR-1000, PR-750B, SS-250
0665463 CUP-FILTER
CB-434, CS-323, CS-431B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.