AVSPARE.COM
parts catalog

CYLINDER HEAD GP 1247372 - Caterpillar



1247372 CYLINDER HEAD GP Caterpillar parts G3412C CYLINDER
Rating:
23
Alternative (cross code) number:
CA1247372
124-7372
1247372
Caterpillar 1247372 CYLINDER HEAD GP
Weight: 305 pounds 138 kg.

Buy CYLINDER HEAD GP 1247372 Caterpillar genuine, new aftermarket tractor parts with delivery
GEN SET ENGINE,

Compatible equipment models: 1247372:

GEN SET ENGINE  G3412C   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Sudden movement of the machine or release of oil under pressure can cause serious injury to persons on or near the machine.To prevent possible injury, perform the procedure that follows before testing and adjusting the hydraulic system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Table 1
Required Tools
Tools Part Number Description Qty
A 4C-8689 Flow Meter 1
8C-6874 Connector 2
6V-8399 O-Ring Seal 2
6V-8942 O-Ring Reducer 2
6V-8556 Nut 2
6V-8398 O-Ring Seal 2
124-2160 Coupling 1
124-2114 Coupling 1
5P-3413 Pipe Sealant 1
122-6889 Hydraulic Hose 36 in
B 4C-6500 Digital Thermometer 1 Note: Perform the following steps before conducting this procedure.
Move the machine to a smooth, horizontal location that is away from operating machines and away from personnel.
Place the propel control lever in NEUTRAL.
Engage the parking brake.
Stop the engine.
Illustration 1 g01049545
Rear Vibratory Motor
(1) T1 port
(2) T2 port
Disconnect hose from T1 (1). Cap the port and plug the hose. Note: If the front motor is being tested, disconnect the hose from the T2 port. Cap the port and plug the hose.
Disconnect hose from T2 port (2), and install Tool A. Orient the flow meter in the direction of flow. The flow travels from the motor to the return manifold. Note: If the front motor is being tested, disconnect the hose from the T1 port, and install Tool A.
Start and operate the engine at HIGH IDLE at 2370 50 rpm. Monitor the hydraulic oil temperature with Tool B. Operate the machine until the oil temperature reaches 43° 5.6°C (110° 10°F).
Read the flow on Tool A. The flow should be less than 3.5 L/min (1.0 US gpm). Note: Motor case drain flow cannot be adjusted. If the case drain flow is greater than the specification, the motor may need to be repaired.
Stop the engine. Remove Tool A. Reconnect the hoses to T1 port (1) and T2 port (2). Repeat for the other vibratory motor.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
G3412C Generator Set Engine 9RR00001-UP


Parts cylinder Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.