AVSPARE.COM
parts catalog

CYLINDER & MTG GP-WHEEL SAW 2278173 - Caterpillar



2278173 CYLINDER & MTG GP-WHEEL SAW Caterpillar parts SW345B, SW60 CYLINDER
Rating:
12
Alternative (cross code) number:
CA2278173
227-8173
2278173
Caterpillar 2278173 CYLINDER & MTG GP-WHEEL SAW

Buy CYLINDER & MTG GP-WHEEL SAW 2278173 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SAW,

Compatible equipment models: 2278173:

WHEEL SAW  SW345B   SW60   Caterpillar
Number on catalog scheme: 3
 
  For full view, you need register

Information:


Illustration 1 g00294754
(A) Stick. (B) Bucket. Note: Assemble this linkage on the machine by rotating the rod end of the bucket cylinder and by positioning the grease fitting away from the stick. Coat all of the bores for pins with lubricant. (1) 093-0097 Shim thickness ... 2.0 mm (.08 inch)Note: Locate the above shim next to the power link. Locate the shims below next to the idler link. (2) Use necessary shims to adjust maximum lateral clearance. Maximum clearance ... 0.8 mm (.03 inch) 134-8865 Shim thickness ... 0.5 mm (.02 inch) 134-8866 Shim thickness ... 1.0 mm (.04 inch) 134-8867 Shim thickness ... 1.6 mm (.06 inch) 134-8868 Shim thickness ... 2.0 mm (.08 inch) (3) 144-1012 Pin Diameter after plating ... 59.86 0.03 mm (2.357 0.001 inch) Minimum thickness for plating ... 0.005 mm (0.0002 inch) (4) 099-0718 Bearing Quantity ... 2 Outside diameter ... 75.085 0.010 mm (2.9561 0.0004 inch) Inside diameter ... 60.125 0.035 mm (2.3671 0.0014 inch) Install the bearing in the bearing bore. ... 5.825 0.800 mm (0.2293 0.0315 inch) (5) Lubricate the sealing lip slightly with the lubricant that is being sealed. (6) 144-1013 Pin Quantity ... 2 Diameter after plating ... 64.77 0.03 mm (2.550 0.001 inch) Minimum thickness for plating ... 0.013 mm (.0005 inch) (7) 099-0721 Bearing Quantity ... 2 Outside diameter ... 80.085 0.010 mm (3.1529 0.0004 inch) Inside diameter ... 65.125 0.035 mm (2.5640 0.0014 inch) Install the bearing in the bearing bore. ... 5.0 0.8 mm (0.20 0.03 inch) (8) Position the four nuts past the end of the four bolts. ... 0.5 mm (.02 inch) (9) Torque for four nuts (8) against four nuts (7) ... 105 20 N m (77 15 lb ft)

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
SW45 & SW60 Wheel Saws WLS00001-UP (MACHINE)
SW345B, SW360B & SW460B Wheel Saws HFS00001-UP (MACHINE)


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.