AVSPARE.COM
parts catalog

CYLINDER & MTG GP-TILT 3079804 - Caterpillar



3079804 CYLINDER & MTG GP-TILT Caterpillar parts CP-56, CP-64, CP-76, CS-56, CS-64, CS-74 CYLINDER
Rating:
50
Alternative (cross code) number:
CA3079804
307-9804
3079804
Caterpillar 3079804 CYLINDER & MTG GP-TILT

Buy CYLINDER & MTG GP-TILT 3079804 Caterpillar genuine, new aftermarket tractor parts with delivery
VIBRATORY COMPACTOR,

Compatible equipment models: 3079804:

VIBRATORY COMPACTOR  CP-56   CP-64   CP-76   CS-56   CS-64   CS-74   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


To prevent possible personal injury, release all the pressure in the hydraulic system before any lines are disconnected.
1. Disconnect hoses (1) from the steering cylinder. Put caps or plugs in the hoses and cylinder to keep out dirt and foreign material.2. Remove nuts (2) [each end of steering cylinder], steering cylinder (3) and spacers from the machine. Use the reverse procedures of Steps 1 and 2 for installation of the steering cylinder (servo-sender).3. Tighten the nuts (2) to a torque of 245 25 N m (180 18 lb.ft.).Disassemble Steering Cylinder (Servo Sender)
START BY:a. remove steering cylinder (servo sender) 1. Remove bolts (2) and heads (4) and (1) from tube (3). 2. Remove rod (7) and piston (6) from rod (5). 3. Remove seal assemblies (8) and ring (9) from piston (6). 4. Remove head (4) from rod (5).5. Remove O-ring seal (10) from head (4). 6. Use tool (A), and remove snap ring (14) from head (4).7. Remove retainer (12) and seal (11) from head (4).8. Remove wiper (13) from retainer (12). 9. Remove two rings (15) from rod (5). Use a press and a spacer with a length of 50.8 mm (2.00 in.) and an outside diameter of not more than 31.75 mm (1.250 in.) and an inside diameter of not less than 25.4 mm (1.00 in.) to remove bearing (16) from rod (5).10. Head (1) (see illustration B68108P1) has the same parts as head (4). For disassembly of head (1), repeat Steps 5 through 9.Assemble Steering Cylinder (Servo Sender)
1. Install ring (1) in the groove of rod (3).2. Use a press and a spacer with a length of 50.8 mm (2.00 in.), and outside diamter of not more than 31.75 mm (1.250 in.) and an inside diameter of not less than 25.4 mm (1.00 in.) to install bearing (2) into rod (3).3. Install ring (4) in the groove of rod (3). 4. Use tool group (B) to install wiper (8) in retainer (7) with the lip of the wiper down. Put clean hydraulic oil on the lip of the seal.5. Install seal (5) in head (6) with the lip of the seal toward the inside. Put clean hydraulic oil on the lip of the seal.6. Use tool (A), and install snap ring (9) in the groove of head (6). 7. Put O-ring seal (10) in position on head (6).8. Repeat Steps 1 through 7 for the installation of parts in the head opposite head (6). 9. Put head (6) in position on rod (3). 10. Install ring (12) and seal assemblies (11) on piston (13). 11. Install piston (13) and rod (14) on rod (3). Put clean lubricant on rod threads, and tighten to a torque of 70 15 N m (50 10 lb.ft.). 12. Put heads (6) and (15) in position on tube (16), and install the bolts that hold it.END BY:a. install steering cylinder (servo sender)

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
CS74 CP74 Vibratory Soil Compactor C8S00001-UP (MACHINE) POWERED BY C6.6 Engine
CS56 CP56 Vibratory Soil Compactor C5P00001-UP (MACHINE) POWERED BY C6.6 Engine
CS64 CP64 Vibratory Soil Compactor C6P00001-UP (MACHINE) POWERED BY C6.6 Engine
CS76 CP76 Vibratory Compactor JCP00001-UP (MACHINE) POWERED BY C6.6 Engine
CS76 XT CP76 Vibratory Compactor C7L00001-UP (MACHINE) POWERED BY C6.6 Engine
CS56 Soil Compactor - Military JMM00001-UP (MACHINE) POWERED BY C6.6 Engine


Parts cylinder Caterpillar catalog:

1923884 CYLINDER GP-TILT
420D, 420E, 428D, 428E, 430D, 430E, 432D, 432E, 438D, 442D, 442E
8J8611 CYLINDER GP-STICK
215, 215B, 215C, 621R
1223755 CYLINDER GP-HYDRAULIC
CW-14, PF-290B, PS-150B, PS-150C, PS-200B, PS-360B, PS-360C
7E8762 CYLINDER HEAD AS
3508, 3512, 3516, 3516B, 5130, 776C, 777B, 784B, 785, 789, 789B, 793, 793B, D11N, D11R
3578008 CYLINDER & MTG GP-HYDRAULIC
2470C, 2570C, 2670C, 553C, 563C, 573C
8X1947 CYLINDER & MTG GP-BLADE LIFT
12H, 12H ES, 12H NA, 12K, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
7E0036 CYLINDER BLOCK AS
225D, 231D, 3208, 613C, PR-1000
1853192 CYLINDER HEAD GP
3054B, 416D, 424D, CS-423E
3119526 CYLINDER GP-BOOM
330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 345C L, 345D, 349D L
1280407 CYLINDER BLOCK AS
3176C, 3196, 345B, 345B L, 480, 65E, 75D, 75E, 85D, 85E, 95E, C-10, C-12
3412802 CYLINDER & SEAL GP-STICK
320D, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.