AVSPARE.COM
parts catalog

CYLINDER GP 3599537 - Caterpillar



3599537 CYLINDER GP Caterpillar parts CYLINDER
Rating:
11
Alternative (cross code) number:
CA3599537
359-9537
3599537
Caterpillar 3599537 CYLINDER GP
Weight: 8 pounds 3 kg.

Buy CYLINDER GP 3599537 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


ASTERN CLUTCH SHAFT BEARINGS
1. Astern clutch shaft. 2. Retainer nut. 3. Bearing assembly (one bearing cup removed). 4. Lock.2. Remove bearing assembly (3) by using the 5F7343 Bearing Pulling Attachment, two 1H3109 Legs, 1H3107 Push Puller, a suitable step plate, 5H9817 Hydraulic Puller and either the 3S6624 Electric Hydraulic Pump or the 9S5800 Pump Group.
REMOVING BEARING ASSEMBLY3. Remove the spacer resting on gear (5). Remove gear (5) from astern clutch shaft (1). The tools necessary for removing gear (5) are the same tools used to remove bearing assembly (3) except use the 1H3110 Bearing Pulling Attachment in place of the 5F7343.4. After gear (5) is removed, remove the gear key from the shaft. Lift the ahead clutch shaft (8) off of the astern clutch shaft (1) and place it on blocks.5. Remove the retainer nut, lock and spacer from shaft (8).
GEAR REMOVAL
5. Gear.6. Remove the bearing assembly (6), the spacer under the bearing and gear (7) from shaft (8) at the same time. Use the same tools which were necessary to remove gear (5) with the addition of 1P516 Plate between the hydraulic puller and the shaft.
GEAR AND BEARING REMOVAL
1. Astern clutch shaft. 6. Bearing assembly. 7. Gear. 8. Ahead clutch shaft.
REMOVING BEARING
9. Bearing.7. Remove the gear key from shaft (8). Remove bearing (9) with the same tools used to remove bearing (6) and gear (7).8. If either bearing (10) or bearing (11) is damaged, it may be necessary to destroy the damaged bearing to remove it from the ahead clutch shaft (8).
AHEAD CLUTCH SHAFT
10. Bearing. 11. Bearing.Astern Clutch Shaft and Ahead Clutch Shaft Assembly
The diameters of the shafts and the bores in the bearings and gears will not allow either the bearings or the gears to be assembled on the shafts incorrectly.Each bearing assembly includes two roller bearing cones, two bearing cups and a spacer between the cups. The bearings are marked to make certain a cone and the corresponding numbered cup will be installed together. The large diameters of the roller bearing cones are installed back to back, this makes it necessary to place bearing cup on the shaft before the first roller bearing cone is installed.
AHEAD CLUTCH SHAFT 1. Race.2. Shield.3. Race.4. Bearing assembly.5. Cup.6. Cones.7. Cup.8. Spacer.9. Shaft assembly.10. Key.11. Gear.12. Spacer.13. Cup spacer.14. Lock.15. Nut.Take care when assembling the shafts because the bearing assembly cups and spacers, the gear keys and the spacer between each gear and bearing assembly can be easily overlooked when installing the heated gears and bearings.1. Install shield (2) in shaft assembly (9).2. Freeze race (1) and install it in shaft assembly (9).3. Heat race (3), bearing assembly (4), gear (11) and bearing cones (6) in hot oil to a temperature of 350° F (176° C).4. Install race (3) and bearing assembly (4).5. Install key (10) and gear (11).6. Install spacer (12), cup (5) and cones (6).7. Allow the assembled parts to cool for four hours.8. Install the 7H7539 Nut and 4K684 Washer (16), FT1506 Plate (17), (with the


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.