AVSPARE.COM
parts catalog

CYLINDER GP 3599594 - Caterpillar



3599594 CYLINDER GP Caterpillar parts CYLINDER
Rating:
16
Alternative (cross code) number:
CA3599594
359-9594
3599594
Caterpillar 3599594 CYLINDER GP
Weight: 39 pounds 17 kg.

Buy CYLINDER GP 3599594 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

1. Remove the carbon from the top inside surface of the cylinder liners.2. Turn the crankshaft until two pistons are at bottom center.3. Remove bearing caps (1) from the two connecting rods. Put pieces of rubber hose or tape on the threads of the connecting rod bolts as protection for the crankshaft. Put identification on each bearing cap so the bearing caps will be installed on the correct connecting rod. 4. Push the pistons up until the piston rings clear the cylinder liner. Remove pistons (2).
Do not turn the crankshaft while any of the connecting rods are in the engine without the caps installed. Do not damage the piston cooling jets when the pistons are removed.
5. Repeat Steps 1 through 4 for the remainder of the pistons.Install Pistons
1. Be sure that the pistons are installed with the flat surfaces (2) of the connecting rods toward each other and the chamfered sides (1) toward the crankshaft. 2. Put clean engine oil on the piston rings and cylinder liners.3. Put two pistons in position opposite of each other in the correct bore of the block. Install pistons (3) with tool (A). For more details on checking bearing clearances and installation of connecting rod bearings, see the topic, "Remove and Install Connecting Rod Bearings" in the Disassembly and Assembly manual.4. Check the bearing clearances with Plastigage.5. Put clean engine oil on bolts (4). Install caps (5) and nuts finger tight. Make sure flat side (6) of each cap is toward the other cap. The chamfered side must be toward the crankshaft. Tighten each nut to a torque of 80 8 N m (60 6 lb ft). Put a mark across the nuts and bolts. Tighten each nut 120 degrees (1/3 turn) more.
Do not use an impact wrench to tighten the nuts the additional 120 degrees.
6. Check the side clearance between two connecting rods on the same crankshaft journal. Clearance must be 0.28 to 0.84 mm (.011 to .033 in) for new rods.7. Repeat Steps 1 through 6 for the remainder of the pistons.End By:a. install oil pumpb. install cylinder headsc. install piston cooling jetsDisassemble & Assemble Pistons
Start By:a. remove pistons
Typical Example1. Remove bearings (3) from the connecting rod and connecting rod cap.2. Remove retainer ring (1) with tooling (A).3. Remove pin (2) and connecting rod (4) from the piston. 4. Remove the piston rings (5) from the piston with tool (B). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning tool. 5. Remove piston skirt (8) from the crown (7). Remove the bearings (9) from the crown. See "Use of Piston Pin Bearing Removal and Installation Tools", Special Instructions, Form No. SMHS7295.6. Heat the connecting rod (4) in an oven to a temperature of 177° to 260°C (350° to 500°F). Never use a direct flame to heat a connecting rod.7. Put connecting rod (4) in position on the base plate


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.