AVSPARE.COM
parts catalog

CYLINDER GP 3599595 - Caterpillar



3599595 CYLINDER GP Caterpillar parts CYLINDER
Rating:
21
Alternative (cross code) number:
CA3599595
359-9595
3599595
Caterpillar 3599595 CYLINDER GP
Weight: 310 pounds 140 kg.

Buy CYLINDER GP 3599595 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Start By:a. remove spacer plateb. remove piston 1. Remove the piston from the cylinder liner that is to be removed. See the topic, "Remove Pistons" in the Disassembly and Assembly manual.2. Turn the crankshaft so that the counterweights on the crankshaft are away from the bottom of the cylinder liner, as shown. 3. Install tooling (A). Use tooling (A) to remove cylinder liner (1) from the block. 4. Remove filler band (2) and seals (3) from the cylinder liner.5. Repeat Steps 1 through 4 for the other cylinder liners, if necessary.Install Cylinder Liners
1. Make sure the bore of the engine block and the cylinder liner are clean. Install cylinder liner (1), without the filler band or seals, in the engine block. 2. Install the spacer plate gasket and spacer plate (2).3. Install tooling (A) around the cylinder liner, as shown. Tighten the four bolts from tooling (A) evenly in four steps: 14 N m (10 lb ft), 35 N m (25 lb ft), 70 N m (50 lb ft), and then to 95 N m (70 lb ft).4. Use two bolts from the cylinder head to hold tooling (B) in position over the cylinder liner. Be sure the crossbar, that is part of tooling (B), is in position at the center of the cylinder liner. Tighten the bolts that hold tooling (B) in place evenly in four steps: 7 N m (5 lb ft), 20 N m (15 lb ft), 35 N m (25 lb ft), and then to 70 N m (50 lb ft).5. Check the distance from the bottom edge of crossbar to the top of the spacer plate. The distance on each end of the crossbar must be the same.6. Check the liner projection with tool (C) at four locations around the liner flange. Liner projection must be 0.03 to 0.15 mm (.001 to .006 in). The difference between the four measurements on the same liner must not be more than 0.05 mm (.002 in). The difference between average liner projection for liners next to each other must not be more than 0.05 mm (.002 in). The maximum difference in the average projection of the cylinder liners under each cylinder head must not be more than 0.10 mm (.004 in). If the liner projection changes too much from point to point around the liner, turn the liner to a new position in the bore. If the projection measurements are still not within specifications, move the liner to a different bore in the cylinder block and check the projection again.7. If a liner does not measure within the correct projection specifications, the projection can be changed with a counterbore operation to the top surface of the cylinder block. The counterbore depth must be in a range from a minimum of 0.030 in. (0.76 mm) to a maximum of 045 in. (1.14 mm). Shims are available to then adjust the liner to the correct projection. See Special Instruction, Form No. FMO55228-03, for procedure to use the 8S3140


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.