AVSPARE.COM
parts catalog

CYLINDER A 9W0007 - Caterpillar



9W0007 CYLINDER A Caterpillar parts CYLINDER
Rating:
46
Alternative (cross code) number:
CA9W0007
9W-0007
9W0007
Caterpillar 9W0007 CYLINDER A
Weight: 136 pounds 61 kg.

Buy CYLINDER A 9W0007 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

2. Loosen the clamps that hold hose (3) in place. Move hose (3) away from elbow (2). 3. Remove the bolts and retainers that hold tube (1) in place in elbow (2).4. Disconnect hose (4) from the elbow.5. Remove the bolts that hold elbow (2) to the water pump. Remove the elbow from the water pump and tube (1).6. Disconnect hose assembly (7) from the water pump.7. Remove bolts (6) that hold the water pump to the adapter.8. Fasten a hoist to water pump (5). Remove the bolts that hold the water pump to the front drive housing, and remove the water pump. The weight of the water pump is 37 kg (82 lb). The following steps are for installation of the water pump.9. Make sure the gasket for the adapter and the O-ring seal on the water pump are in position. Put clean engine oil on the O-ring seal.10. Fasten a hoist to water pump (5). Put the water pump in position on the engine, and install the bolts that hold it.11. Install bolts (6) to hold the adapter to the water pump.12. Connect hose assembly (7) to the water pump.13. Make sure the O-ring seals are in position on the end of tube (1) and in elbow (2). Put clean engine oil on the O-ring seals.14. Put elbow (2) in position on tube (1) and the water pump. Install the bolts that hold the elbow to the water pump.15. Install the retainers and bolts that hold tube (1) in position in the elbow.16. Put hose (3) in position on elbow (2), and tighten the clamps that hold it in place.17. Connect hose (4) to the water pump.18. Fill the cooling system with coolant to the correct level. See the Maintenance Manual.Disassemble Water Pump
Start By:a. remove water pump 1. Remove O-ring seal (4) from the back of housing assembly (3).2. Remove washer (1) that holds shaft assembly (2) in housing assembly (3).
Typical Example3. Remove cover (5) from housing assembly (3). Remove the O-ring seal from cover (5).
Typical Example4. Loosen nut (7) and the washer that hold impeller (6) to the pump shaft Use tooling (A) to loosen impeller (6) from the end of the pump shaft Remove tooling (A), nut (7), the washer and impeller (6) from the pump shaft and housing assembly (3).
Typical Example5. Remove spring (9) from seal assembly (8) and shaft assembly (2).6. Use a soft hammer, and push shaft assembly (2) out of seal assembly (8) and housing assembly (3). Remove seal assembly (8) from housing assembly (3). 7. Remove ceramic seal (10) from the rubber ring. Remove the rubber ring from housing assembly (3). 8. Remove seal (11) from the back of housing assembly (3).Assemble Water Pump
1. If necessary, make a replacement of the two filters in the pump housing at location (1).2. If necessary, make a replacement of plug (2) and the seal.
The cardboard sleeve is required to slightly stretch the inner diameter of the seal to prevent seal damage when


Parts cylinder Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.