AVSPARE.COM
parts catalog

DOOR GP-ACCESS 2332981 - Caterpillar



2332981 DOOR GP-ACCESS Caterpillar parts M316C, M318C, M318C MH, M322C DOOR
Rating:
20
Alternative (cross code) number:
CA2332981
233-2981
2332981
Caterpillar 2332981 DOOR GP-ACCESS

Buy DOOR GP-ACCESS 2332981 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEELED EXCAVATOR,

Compatible equipment models: 2332981:

WHEELED EXCAVATOR  M316C   M318C   M318C MH   M322C   Caterpillar
Number on catalog scheme: 9
 
  For full view, you need register

Information:


Table 2
Resistance Measurements for the Coolant Level Circuit
Connector and Terminal Terminal
P1-44 (engine coolant level)
P2-74 (SCAC coolant level) All of the terminals on the P1 connector
All of the other terminals on the P2 connector
Engine ground stud
Table 3
Troubleshooting Test Steps Values Results
6. Check the Harness Wiring for a Short Circuit
A. Turn the main disconnect switch to the OFF position.
B. Disconnect the J1/P1 and the J2/P2 ECM connectors. Also, disconnect the connector for the coolant level sensor.
C. Measure the resistance between the points that are listed in Table 2.
Wiggle the harness during the following measurements in order to reveal an intermittent condition.
Short circuit Result: Each check of the resistance indicates an open circuit. There is not a short circuit to another wire in the harness.
Proceed to Test Step 7.
At least one check of the resistance does not indicate an open circuit. There is a short to another wire in the harness. The problem may be with a connector.
Repair the wire and/or the connector, when possible. Replace damaged parts, if necessary.
Verify that the repair eliminates the problem.
7. Check the Operation of the ECM
A. Fabricate a jumper wire that is long enough to provide a test circuit across the ECM connectors. Crimp connector sockets to each end of the jumper wire.
B. Remove the wires from terminal locations P2-30 (secondary ECM return) and P1-44 (primary ECM coolant level). Install the jumper wire into these terminal locations.
Or, remove the wires from terminal locations P2-30 (secondary ECM return) and P2-74 (primary ECM SCAC coolant level). Install the jumper wire into these terminal locations.
C. Restore electrical power to the ECM.
D. Use Cat ET to monitor the status for "Coolant Level". Use a wire removal tool to remove the jumper wire and check the status again.
Wait at least 30 seconds for activation of the status indicator.
E. Turn the main disconnect switch to the OFF position.
Restore all wiring to the original configuration.
Operation of ECM
Result: The status is "LOW" when the jumper wire is not connected. The status is "OK" when the jumper wire is connected.
The ECM is properly reading the switch input. There may be an intermittent problem in the harness or in a connector. If an intermittent electrical problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect" for troubleshooting information.
Result:The status is "LOW" when the jumper wire is connected.
RepairReplace the ECM. Refer to Troubleshooting, "Test ECM Mode".
Note: Before you consider replacing the ECM, consult with the Dealer Solutions Network (DSN) for assistance.
Verify that the repair eliminates the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
M318C Excavator BCZ00001-02000 (MACHINE) POWERED BY 3056 Engine
M316C Excavator BDX00001-02000 (MACHINE) POWERED BY 3056 Engine
M322C Excavator BDK00001-02000 (MACHINE) POWERED BY 3056 Engine
M322C Excavator BDY00001-02000 (MACHINE) POWERED BY 3056 Engine
M318C Material Handler BEB00001-02000 (MACHINE) POWERED BY 3056E Engine
M318C Excavator BCZ02001-UP (MACHINE) POWERED BY 3056E Engine
M316C Excavator BDX02001-UP (MACHINE) POWERED BY 3056E Engine
M322C Excavator BDK02001-UP (MACHINE) POWERED BY 3056E Engine
M322C Excavator BDY02001-UP (MACHINE) POWERED BY 3056E Engine
M318C Material Handler BEB02001-UP (MACHINE) POWERED BY 3056E Engine
M318C Excavator H2D00001-UP (MACHINE) POWERED BY 3056E Engine
M316C Excavator H2C00001-UP (MACHINE) POWERED BY 3056E Engine
M322C Excavator H2E00001-UP (MACHINE) POWERED BY 3056E Engine
M322C Excavator H2G00001-UP (MACHINE) POWERED BY 3056E Engine
M318C Excavator H2F00001-UP (MACHINE) POWERED BY 3056E Engine


Parts door Caterpillar catalog:

1938990 DOOR GP-ACCESS
M318C, M318C MH, M322C
1892768 DOOR & MTG GP-CAB
307C, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 315C, 315D L, 318C, 319C, 319D, 319D L, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 322C, 323D L, 323D LN, 324D, 324D L, 324D LN...
1938993 DOOR AS
M313C, M315C, M316C, M318C, M322C
2213167 DOOR AS
M318C, M318C MH, M322C
2015673 DOOR AS
M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH
2195266 DOOR AS
M313C, M315C, M316C, M318C, M322C
2211547 DOOR AS
M315C, M316C, M318C, M318C MH
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.