AVSPARE.COM
parts catalog

DRIVE GP-SWING 1695528 - Caterpillar



1695528 DRIVE GP-SWING Caterpillar parts 345B II, 345B II MH, 345B L, W345B II DRIVE
Rating:
17
Alternative (cross code) number:
CA1695528
169-5528
1695528
Caterpillar 1695528 DRIVE GP-SWING

Buy DRIVE GP-SWING 1695528 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, WHEELED EXCAVATOR,

Compatible equipment models: 1695528:

EXCAVATOR  345B II   345B II MH   345B L  
WHEELED EXCAVATOR  W345B II   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 62 g02807941
Remove the plug
Remove plug (2) .
Illustration 63 g02807956
Set speed by turning adjusting screw
Adjust speed. If Ng exceeds TMI specifications, tighten the adjusting screw. If Ng is less than the specified value, loosen the adjusting screw.
Illustration 64 g02807957
Adjust the maximum-speed stopper bolt
Adjust the maximum-speed stopper bolt until the speed at the start of high-speed control is Nf.
Check that the no-load maximum speed is Ng (described in Step 1). Continue adjustment until the specified value is obtained.
Illustration 65 g02807958
Increase pump speed to make sure that the control rack position reaches Ra.
Illustration 66 g02807959
Full-load Adjustment
Illustration 67 g02807997
Install the cover and adjust full-load stopper bolt
Install cover (3) on governor using bolts and lockwashers (2). Use caution when installing the cover to make sure that the O-ring seal is in the seal groove.
Illustration 68 g02807999
Position the control lever at maximum-speed position.
Adjust full-load stopper bolt (1) to the f"ull-load fuel injection quantity" position. See TMI for the specifications (Point A).
Install cap.Control Lever Angle Measurement
Illustration 69 g02808016
Measuring control lever angle at the "full-speed" and "idling" positions.
Measuring the control lever angle at the "idling" and "full" positions.
If the angle is not as specified by TMI, replace the shifters shim. If the control lever is positioned toward the "full" position, replace the shifters shim with a thicker one. When control lever is toward the "idling" position, replace the shim with a thinner one.Check Starting Delivery
Illustration 70 g02808018
Remove measurement adapter
Remove measurement adapter (1) .
Illustration 71 g02808038
Cap must be installed to check delivery rate
Install cap (2) .
Run pump at speed specified in TMI.
Check delivery rate with specifications listed in TMI.
Stop pump rotation.
Illustration 72 g02808058
Adjusting screw for setting fuel flow
If delivery rate does not meet TMI specifications, remove cap (2), loosen lock nut, and adjust screw (3). Adjusting screw outward decreases fuel flow and inward increases fuel flow.
Install cap (2) and recheck delivery rate. Repeat Steps 2 through 6 until delivery rate is at specified value.Lockwiring Caps of Adjustment Screws
All adjustment stops (screws) that directly affect engine performance should be lockwired after adjustment. Do not readjust any stop without using the test stand can adversely affect the engine and engine performance.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
345B, 345B L & 345B LC Excavator 2SW00001-UP (MACHINE) POWERED BY 3176C Engine
345B L Series II Excavators AGS00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Material Handler APB00001-UP (MACHINE) POWERED BY 3176C Engine
W345B Series II Material Handlers ANJ00001-UP (MACHINE) POWERED BY 3176C Engine
345B & 345B L Series II Excavators AKJ00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Excavators ALD00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Material Handler DET00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Excavator CCC00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine
345B SERIES II MATERIAL HANDLER (CUSTOM) AKX00001-UP (MACHINE) POWERED BY 3176C ENGINE


Parts drive Caterpillar catalog:

1557063 DRIVE GP-WINDOW
325B, 325B L, 330B, 345B II
1994726 DRIVE GP-FINAL
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L
1557064 DRIVE GP
325B, 325B L, 330B, 345B II
6N3826 DRIVE AS-MOTOR
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140H, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16H, 16H NA, 16M, 2290, 2390, 2391,...
1695532 DRIVE GP-SWING
345B II, 345B II MH, 345B L, W345B II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.