AVSPARE.COM
parts catalog

DRIVE GP-SWING 1695532 - Caterpillar



1695532 DRIVE GP-SWING Caterpillar parts 345B II, 345B II MH, 345B L, W345B II DRIVE
Rating:
22
Alternative (cross code) number:
CA1695532
169-5532
1695532
Caterpillar 1695532 DRIVE GP-SWING

Buy DRIVE GP-SWING 1695532 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, WHEELED EXCAVATOR,

Compatible equipment models: 1695532:

EXCAVATOR  345B II   345B II MH   345B L  
WHEELED EXCAVATOR  W345B II   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Illustration 10 g03268119
Assemble two o-ring seals, (16) and (20), to new connector (22). Install the connector (22) into the left-hand port in the tube assembly (12). Connect the one end of hose assembly (9) to the connector (22). Connect the other end of hose assembly (9) to the solenoid valve group (5) .
Illustration 11 g03319774
Connect new control harness assembly (6) to the solenoid valve group (5). Route the harness along the transmission harness. Secure control harness (6) to the transmission harness with 15 cable straps (18). Secure the control harness assembly (6) to the plate assembly (8) with three cable straps (27). Connect the longer lead of the control harness assembly (6) to the chassis harness and secure with the clip (2) at the front of plate assembly (8). Connect the shorter lead to the lead from the solenoid valve group (7). Secure the connector in the existing clip. Secure the extra harness lead with cable strap (27) .
Illustration 12 g03332910
Connect Cat ET up to machine to enable the starting arrangement. In the Tractor Transmission ECM under Machine Configuration, change "Cold Engine Parasitic Load Reduction Installation" from Not Installed to Installed.Procedure to Install Clutch Group for 382-2789 Cold Weather Starting Ar
Illustration 13 g03514498
Remove bottom guards (A) .
Illustration 14 g03514499
Disconnect hoses and harnesses from fan and brake valve (B) at front of case.
Remove fan and brake valve (B) .
Remove mounting plate for fan and brake valve (B) .
Illustration 15 g03514500
Remove brake cooling pump (C) at rear of tractor transmission.
Illustration 16 g03514501
Remove drive shaft (D) .
Illustration 17 g03514502
Remove scavenge pump (E) from rear of the transfer gear box (F) .
Illustration 18 g03514503
Remove transfer gear box (F) .
Illustration 19 g03514504
Remove friction discs (G) and flywheel (H). Discard the part.
Illustration 20 g03514505
Install clutch group (33) with eight bolts (34) and eight hard washers (35). Tighten bolts (34) to 300 40 N m (221 29 lb ft).
Fill volume between flywheel and clutch pressure plate with 200 mL (7 oz) SAE 30 oil.
Reinstall parts in reverse order of disassembly.Note: Verify drive shaft end play is to specification. Bolt depth is determined with assembly of the coupling and retaining ring. There should be a maximum clearance of 3 mm (0.1 inch) between the coupling and retaining ring that assembles to the transfer gear. If bolt and nut in end of shaft need adjusted, apply red Loctite 271 to the threads of the bolt and nut.
Illustration 21 g03514507
Connect Cat ET up to machine to enable the starting arrangement. In the Tractor Transmission ECM under Machine Configuration, change "Cold Engine Parasitic Load Reduction Installation" from Not Installed to Installed.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
345B, 345B L & 345B LC Excavator 2SW00001-UP (MACHINE) POWERED BY 3176C Engine
345B L Series II Excavators AGS00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Material Handler APB00001-UP (MACHINE) POWERED BY 3176C Engine
W345B Series II Material Handlers ANJ00001-UP (MACHINE) POWERED BY 3176C Engine
345B & 345B L Series II Excavators AKJ00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Excavators ALD00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Material Handler DET00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Excavator CCC00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine


Parts drive Caterpillar catalog:

1557063 DRIVE GP-WINDOW
325B, 325B L, 330B, 345B II
1994726 DRIVE GP-FINAL
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L
1557064 DRIVE GP
325B, 325B L, 330B, 345B II
6N3826 DRIVE AS-MOTOR
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140H, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16H, 16H NA, 16M, 2290, 2390, 2391,...
1695528 DRIVE GP-SWING
345B II, 345B II MH, 345B L, W345B II
1695530 DRIVE GP-SWING
345B II, 345B II MH, 345B L, W345B II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.