AVSPARE.COM
parts catalog

DRIVESHAFT GP 3599573 - Caterpillar



3599573 DRIVESHAFT GP Caterpillar parts DRIVESHAFT
Rating:
16
Alternative (cross code) number:
CA3599573
359-9573
3599573
Caterpillar 3599573 DRIVESHAFT GP
Weight: 52 pounds 23 kg.

Buy DRIVESHAFT GP 3599573 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Start By:a. remove valve covers 1. Use tooling (A) to disconnect three adapters (4) and (5).2. Remove three nuts (2) and locknuts (3).3. Remove three fuel lines (1). 4. Remove the cover from the flywheel housing and install tool (B). Use tool (B) to turn the crankshaft to release any pressure against the rocker arms.5. Use tool (C) to move the rocker arms away from push rods (6) far enough so the push rods can be removed. 6. Put identification on valve bridges (9) as to their location for correct installation. Remove valve bridges (9).7. Remove bolts (7) and rocker shaft assembly (8).Install Rocker Shaft Assembly
1. Put rocker shaft assembly (8) in position.2. Put clean engine oil on bolts (7). Install three bolts (7). 3. Use the following procedure to tighten bolts (7). a. Tighten bolts (10) through (15) in numerical sequence to 280 27 N m (210 20 lb ft).b. Tighten bolts (10) through (15) in numerical sequence to 440 20 N m (320 15 lb ft).c. Do Step 3b again to make sure all the bolts are tightened to the correct torque.4. Put clean engine oil on the valve bridge dowels. Install valve bridges (9) in their original positions on the engine. 5. Use tool (A) to make sure there will be no pressure against push rod (16) and rocker arm (17). Use tool (B) to pull rocker arm (17) away from push rod (16). Put push rod (16) in position under the rocker arm. If the rocker arm can not be moved enough to put the push rod in position, turn the crankshaft with tool (A).6. Make an adjustment of the valves to have a clearance of .038 mm (.015 in) for intake and 0.76 mm (.030 in) for exhaust. See VALVE CLEARANCE SETTING in TESTING AND ADJUSTING. 7. Make sure the O-ring seal is in position on the adapter. Put clean engine oil on the O-ring seal. Put adapters (4) and (5) with fuel lines (1) in position in the valve cover base.8. Install locknuts (3) and nut (2). Tighten locknuts (3) to a torque of 30 7 N m (22 5 lb ft). Tighten nut (2) to a torque of 41 7 N m (30 5 lb ft).9. Use tool (C) to tighten adapters (4) and (5) to a torque of 41 7 N m (30 5 lb ft).End By:a. install valve coverDisassemble Rocker Shaft Assembly
Start By:a. remove rocker shaft assembly 1. Remove retainer (3), washers (2) and rocker arm (4) from the rocker shaft assembly.2. Make sure dowel (1) is free of oil. 3. Put tooling (A) in position on dowel (1). Pull rocker arm (6) away from bracket assembly (5). Remove the dowel with tooling (A). Remove bracket assembly (5). 4. emove rocker arms (9), spring (8) and brackets (7). Use tooling (A) to remove the dowel that holds bracket assembly (6) on the rocker shaft. 5. Remove nuts (10) and


Parts driveshaft Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.