AVSPARE.COM
parts catalog

EDGE 2332923 - Caterpillar



2332923 EDGE Caterpillar parts 305.5D, 305.5E, 305D CR, 305E EDGE
Rating:
34
Alternative (cross code) number:
CA2332923
233-2923
2332923
Caterpillar 2332923 EDGE

Buy EDGE 2332923 Caterpillar genuine, new aftermarket tractor parts with delivery
MINI HYD EXCAVATOR,

Compatible equipment models: 2332923:

MINI HYD EXCAVATOR  305.5D   305.5E   305D CR   305E   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Table 2
Troubleshooting Test Steps Values Results
1. Check For Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Download the "Product Summary Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
D. Use the electronic service tool to check that coolant temperature, intake manifold air temperature, and NRS temperature are all at least 5° C (41° F).
Note: Wait at least 10 seconds in order for the diagnostic codes to become active.
E. Use the electronic service tool in order to monitor active diagnostic codes or recently logged diagnostic codes. Look for an active or logged -3 or -4 codes for the pressure sensor or the barometric pressure sensor.
F. Use the electronic service tool in order to monitor active diagnostic codes or recently logged diagnostic codes. Look for an active or logged -13 code for a pressure sensor or the barometric pressure sensor.
G. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: There are no active diagnostic codes for the pressure sensors.
If there are logged diagnostic codes for the intake manifold pressure sensor, the fault may be intermittent.
Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" in order to identify intermittent faults.
Result: One or more of the temperature sensors is reading less than 5° C (41° F).
Proceed to Test Step 4.
Result: There is an active -3 or -4 diagnostic code for a pressure sensor or the barometric pressure sensor.
Repair: Troubleshoot these codes before continuing with this procedure.
Result: 3358-13 or 3385-13and 3563-13 or 1785-13 diagnostic codes are active.
Proceed to Test Step 5.
Result: There is an active 3358-13, 3385-13, 3563-13 or 1785-13 diagnostic code for only one sensor.
Proceed to Test Step 6.
There is an active 411-13 or 3387-13 diagnostic code.
Proceed to Test Step 2.
2. Check the Signal Wire for a Short Circuit
A. Turn the keyswitch to the OFF position.
B. Disconnect the P2 connector and disconnect the connector from the suspect sensor.
C. Check the resistance between the applicable signal terminal on the P2 connector and all other terminals on the P2 connector.
Greater than 100 Ohms
Result: At least one of the resistance measurements is less than 100 Ohms. The fault is in the engine harness.
Repair: Repair the faulty connector or replace the faulty harness. Use the electronic service tool to verify that the repair eliminates the fault.
Result: All resistance measurements are greater than 100 Ohms.
Proceed to Test Step 3.
3. Create a Short Circuit at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the suspect sensor.
C. Fabricate a jumper wire that is 150 mm (6 inch) long. Crimp a terminal to both ends of the wire.
D. Use the jumper to connect the sensor signal terminal to the sensor ground terminal on the harness connector for the suspect sensor.
E. Turn the keyswitch to the ON position. Do not start the engine.
F. Access the "Active Diagnostic Codes" screen on the electronic service tool and check for an active XXXX-4 diagnostic code for the

Caterpillar parts catalog:

Caterpillar parts catalog
305D Mini Hydraulic Excavator XER00001-UP (MACHINE) POWERED BY S4Q2T Engine
305.5D Mini Excavator FLZ00001-UP (MACHINE) POWERED BY S4Q2T Engine
305.5E Mini Hydraulic Excavator FKY00001-UP (MACHINE)
305E Mini Hydraulic Excavator XFA00001-UP (MACHINE) POWERED BY C2.4 Engine
305E2 CR Mini Hydraulic Excavator DJX00001-UP (MACHINE) POWERED BY C2.4 Engine
305.5E2 CR Mini Hydraulic Excavator EJX00001-UP (MACHINE) POWERED BY C2.4 Engine


Parts edge Caterpillar catalog:

3036250 EDGE-RH
304C CR, 305.5E, 305C CR, 305E
3036251 EDGE-LH
304C CR, 305.5E, 305C CR, 305E
2460186 EDGE
305.5D, 305.5E, 305D CR, 305E
2555140 EDGE
305.5D, 305.5E, 305D CR, 305E
2332913 EDGE
305.5D, 305.5E, 305D CR, 305E
1803638 EDGE-CUTTING
305.5D, 305.5E, 305D CR, 305E
1803647 EDGE-CUTTING
305.5D, 305.5E, 305D CR, 305E
2142154 EDGE-CUTTING
305.5D, 305.5E, 305D CR, 305E
1803648 EDGE-CUTTING
305.5D, 305.5E, 305D CR, 305E
2139645 EDGE-CUTTING
305.5D, 305.5E, 305D CR, 305E
2446281 EDGE-CUTTING
305.5E, A13, A19, A26, A26B, A7, A7B
4333945 EDGE
305.5E, 305E
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.